Multi-Tech Systems RAS96 manual E1 Command Messages, E1 Status LEDs

Page 61

5 E1 Daughter Card

E1 Command Messages

The system can display the following E1 command messages:

Message: E1 Settings have not been changed

Meaning: Either the E1SETUP command parameters were not changed, or the

E1CFG command was not entered.

Recovery: Start over at step 1 of the command example, re-provision the appropriate menu(s), and enter the E1CFG command to implement the changes to the E1 Daughter Card configuration.

Message: ERROR: Illegal command.

Meaning: The command was typed incorrectly, or an unsupported command was entered.

Recovery: Re-check the command syntax and start over at step 1 of the command example.

Message: Missing device specifier (e.g., 1A) or missing devices.

Meaning: The slot number entered in the E1STATUS xy command was incorrect.

Recovery: Re-check the slot number of the E1 Daughter Card and start over at step 1 of the command example.

E1 Status LEDs

The RASCard front panel contains fourteen indicators (seven for each optional port) that show the status of the RASCard’s optional E1 port.

LED Indicator	Color	Indication

ONLINE	Green	On indicates that the E1 card is online and no errors are detected.
		Off indicates that the E1 card is offline due to one of the following e
RED ALARM	Red	On indicates that a loss of E1 signal has been detected.
		Off indicates that the E1 card is detecting an incoming E1 signal.
YELLOW ALARM Red		On indicates that the remote E1 channel bank or network is in red a
		transmitting a yellow frame pattern.
		Off indicates that the remote channel bank or network is not transm
		yellow alarm.
SYNC LOSS	Red	On indicates that the E1 card has lost synchronization with the fram
		boundaries on the receive E1 line.
		Off indicates that the E1 card is synchronized with the receive E1 l
BPV VIOLATION	Red	On indicates that a received bipolar violation (BPV) is being detect
		Off indicates that no BPV is being detected.
RAI ALARM	Red	REMOTE ALARM INDICATION
		On indicates that the E1 card is receiving unframed all 1s, indicatin
		disconnection or attached device failure.
		Off indicates that the attached device is operating correctly.
TEST MODE	Red	On indicates that the E1 card is in one of several possible test mod
		Off indicates that the E1 card is not in a test mode.

CommPlete Communications Server

53

Image 61

Contents RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Iii Important Safety InstructionsTable of Contents Appendix C Post Codes Solving ProblemsPage Introduction Manual Organization IntroductionAppendix B Post Messages Technical SpecificationsAppendix C Post Codes Appendix D Approved MemoryHumidity range 20-90% noncondensing RASCard Description RAS96 RASCard Memory BanksJumpers J17 Watchdog TimerJ14, J15, J16, J18 CPU Frequency Selection Internal Connectors J2 Power Connector External ConnectorsJ22 E1 Alarm J35 VideoFront Panel LED IndicatorsEthernet Status LEDs E1 Status LEDsPower Switch SwitchesReset Switch Page Installation Pre-Installation Notes Safety WarningsInstallation Procedure Installation Page Bios Setup Utility Starting Setup Case of Problems Using SetupGetting Help Bios Features Setup Standard Cmos SetupChipset Features Setup Power Management SetupPassword Setting PCI Configuration SetupLoad Bios Defaults IDE HDD Auto Detection Load Setup DefaultsExit Without Saving Save and Exit SetupDate Standard Cmos SetupTime Hard DisksVideo Drive a Type / Drive B TypeCGA Memory Halt OnEnabled Bios Features SetupDisabled Virus WarningBoot Sequence Quick Power On Self TestBoot Up Floppy Seek Boot Up NumLock StatusGate A20 Option Typematic Rate SettingMemory Parity Check Typematic Rate Chars/SecVideo Bios Shadow Typematic Delay MsecSecurity Option C8000 Cffff Shadow/DC000 Dffff ShadowSystem Bios Cacheable Chipset Features SetupDram Timing Bit I/O Recovery Time Video Bios CacheableIDE HDD Block Mode Memory Hole At 15M-16MPCI Concurrancy On-Chip Primary PCI IDEPCI Streaming PCI BurstingPower Management Power Management SetupStandby Mode Doze ModeSuspend Mode HDD Power DownCOM Ports Accessed Power Down ActivitiesLPT Ports Accessed Drive Ports AccessedSlot x Using INT# PCI Configuration Setup1st/2nd/3rd/4th Available IRQ PCI IDE IRQ Map to PCI IRQ Activated byEnter Password Password SettingPage E1 Daughter Cards E1 Overview SpecificationsE1 Glossary E1 Basics E1 Frame Formats Signaling OptionsE1 Line Coding Dnis digitsCountry Selection E1 Facility Termination Pin SignalPCB Description RJ-11 Alarm JackE1 Line Monitoring Jack Test ModesOrdering an E1 Line Configuration of the E1 Daughter CardChannelized E1 line with 30 DS-0 channels E1 Frame Format Line CodingFactory Defaults To Configure the E1 Daughter CardCommand Example E1 CommandsRAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Status LEDs E1 Command MessagesFunctional Description Solving Problems RASCard has no video TroubleshootingCOM1 port does not respond correctly Invalid time, date or setupKeyboard does not respond to key strokes Memory Upgrade Calling Technical Support Diagnostic TestsRAS96 RASCard User Guide Appendixes Keyboard Connector J11 Appendix a Connector PinoutsVideo Connector J35 E1 Alarm Connector J22 COM1 Connector J3Drive Power Connector J13 Pin Floppy Disk Drive Connector J27IOCS16 Hard Disk Connector J6Figure A-7. IDE connector IDE Connector J21Appendix B Post Messages Error MessagesPost Beep Memory parity Error at Memory Address Error atMemory Verify Error at Offending Segment Code Name Description Appendix C Post CodesPost Codes E1-EF Capacity Speed Type Manufacturer Part Number Usable MB Appendix D Approved MemoryAppendix E Regulatory Information EMC, Safety and Terminal Directive Compliance