Multi-Tech Systems RAS96 manual To Configure the E1 Daughter Card, Factory Defaults

Page 56

RAS96 RASCard User Guide

To Configure the E1 Daughter Card

1.Turn on power to the segment containing the E1 Card to be configured.

2.Log in to the controller as supervisor, supervisor and type the command E1status 1b (5b, 9b, or 13b) for E1-1 at the A:# prompt. The E1 Card Status screen is displayed.

3.If the line settings do not match the line settings of your E1 line, type the command E1setup 1b (5b, 9b, or 13b) at the A:# prompt.

4.The E1 setup will take you through a series of menus where you will enter the information that was gathered in the Installation Overview.

Factory Defaults:
Framing:	CRC4
Line Coding:	HDB3
Signaling Options:	R2 digital

5.When you save the changes at the end, the E1 parameters are then sent to the E1 card for configuration.

48	CommPlete Communications Server

Image 56

Contents RAS96 RASCard E1 User Guide RAS96 RASCard User Guide Important Safety Instructions IiiTable of Contents Solving Problems Appendix C Post CodesPage Introduction Introduction Manual OrganizationTechnical Specifications Appendix B Post MessagesAppendix C Post Codes Appendix D Approved MemoryHumidity range 20-90% noncondensing RASCard Description Memory Banks RAS96 RASCardJ14, J15, J16, J18 CPU Frequency Selection J17 Watchdog TimerJumpers Internal Connectors External Connectors J2 Power ConnectorJ22 E1 Alarm J35 VideoLED Indicators Front PanelEthernet Status LEDs E1 Status LEDsReset Switch SwitchesPower Switch Page Installation Installation Procedure Safety WarningsPre-Installation Notes Installation Page Bios Setup Utility Starting Setup Getting Help Using SetupCase of Problems Standard Cmos Setup Bios Features SetupChipset Features Setup Power Management SetupLoad Bios Defaults PCI Configuration SetupPassword Setting Load Setup Defaults IDE HDD Auto DetectionSave and Exit Setup Exit Without SavingStandard Cmos Setup DateTime Hard DisksCGA Drive a Type / Drive B TypeVideo Halt On MemoryBios Features Setup EnabledDisabled Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek Boot Up NumLock StatusTypematic Rate Setting Gate A20 OptionMemory Parity Check Typematic Rate Chars/SecTypematic Delay Msec Video Bios ShadowSecurity Option C8000 Cffff Shadow/DC000 Dffff ShadowDram Timing Chipset Features SetupSystem Bios Cacheable Video Bios Cacheable Bit I/O Recovery TimeIDE HDD Block Mode Memory Hole At 15M-16MOn-Chip Primary PCI IDE PCI ConcurrancyPCI Streaming PCI BurstingPower Management Setup Power ManagementDoze Mode Standby ModeSuspend Mode HDD Power DownPower Down Activities COM Ports AccessedLPT Ports Accessed Drive Ports Accessed1st/2nd/3rd/4th Available IRQ PCI Configuration SetupSlot x Using INT# PCI IRQ Activated by PCI IDE IRQ Map toPassword Setting Enter PasswordPage E1 Daughter Cards Specifications E1 OverviewE1 Glossary E1 Basics Signaling Options E1 Frame FormatsE1 Line Coding Dnis digitsCountry Selection Pin Signal E1 Facility TerminationRJ-11 Alarm Jack PCB DescriptionE1 Line Monitoring Jack Test ModesConfiguration of the E1 Daughter Card Ordering an E1 LineChannelized E1 line with 30 DS-0 channels E1 Frame Format Line CodingTo Configure the E1 Daughter Card Factory DefaultsE1 Commands Command ExampleRAS96 RASCard User Guide E1 Daughter Card RAS96 RASCard User Guide E1 Command Messages E1 Status LEDsFunctional Description Solving Problems Troubleshooting RASCard has no videoKeyboard does not respond to key strokes Invalid time, date or setupCOM1 port does not respond correctly Memory Upgrade Diagnostic Tests Calling Technical SupportRAS96 RASCard User Guide Appendixes Video Connector J35 Appendix a Connector PinoutsKeyboard Connector J11 COM1 Connector J3 E1 Alarm Connector J22Pin Floppy Disk Drive Connector J27 Drive Power Connector J13Hard Disk Connector J6 IOCS16IDE Connector J21 Figure A-7. IDE connectorPost Beep Error MessagesAppendix B Post Messages Memory Verify Error at Memory Address Error atMemory parity Error at Offending Segment Appendix C Post Codes Code Name DescriptionPost Codes E1-EF Appendix D Approved Memory Capacity Speed Type Manufacturer Part Number Usable MBEMC, Safety and Terminal Directive Compliance Appendix E Regulatory Information