Multi-Tech Systems MT5634ZLX/FE manual EMC, Safety and Terminal Directive Compliance

Page 63

Appendices

EMC, Safety and Terminal Directive Compliance

The CE mark is affixed to this product to confirm compliance with the following European Community Directives:

Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of Member States relating to electromagnetic compatibility.

and

Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits:

and

Council Directive 98/13/EEC of 12 March 1998 on the approximation of the laws of Member States concerning telecommunications and Satellite earth station equipment.

Commission Decision "CTR21"

The equipment has been approved to [Commission Decision"CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

This equipment is designed to work with PSTN networks that accept analog signals. Multi-Tech does not currently know of any interoperating difficulties.

In the event of problems, you should contact your equipment supplier in the first instance.

New Zealand Telecom Warning Notice

Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to ‘bell tinkle’ or noise and may also cause a false answer condition. Should such problems occur, the user should NOT contact the Telecom Faults Service.

The preferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic) dialing and is readily available on almost all New Zealand telephone exchanges.

Warning Notice: No '111' or other calls can be made from this device during a mains power failure.

International Modem Restrictions

Some dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause a modem to become non-compliant with national telecom requirements in specific countries. Also note that some software packages may have features or lack restrictions that may cause the modem to become non-compliant.

MT5634ZLX/FE

63

Image 63
Contents User Guide Revision Description User GuideContents Index Introduction and Description MultiMobile User Guide IntroductionProduct Description Fast EthernetAuto-negotiation Category 3 and Category 5 Ethernet CablingIntroduction and Description Technical Specifications Features System Requirements Quick Start Unpacking Safety Warning TelecomQuick Start MT5634ZLX/FE LAM InformationMT5634ZLX/FE Installation Installing the MT5634ZLX/FE CardMODEM-LAM LEDs LED IndicatorsLink Ethernet LAMAct 10/100Windows 98 Installation Installing Driver and Modem SoftwareMT5634ZLX/FE Add New Hardware Wizard dialog box is displayed Windows 95 Installation Quick Start Open My Computer Control Panel Network Windows NT 4.0 InstallationMT5634ZLX/FE Installation in NT Getting Started with Windows NTMT5634ZLX/FE Modem configuration for NT Quick Start MT5634ZLX/FE Click Startup Windows NT 3.51 InstallationGetting Started with Windows NT3.51 Open Program Manager Main group Control Panel NetworkSelect Other Requires Disk from Manufacturer Click Continue Click Do not detect for the network adapterArtisoft Lantastic 6.0 Installation Novell NetWare InstallationFor Non-Windows 95/98/NT Systems PROTOCOL.INI MS LAN Manager InstallationPacket Driver Installation Windows for Workgroups 3.11 InstallationSelect Enhanced mode NDIS3 for.... then click OK ATEnter Understanding AT CommandsUsing the Windows 95/98/NT HyperTerminal Program Basic Modem OperationDialing and Answering Techniques MT5634ZLX/FE AT Commands, S-Registers and Result Codes AT&K3H0Enter How To Use AT CommandsAT Commands, S-Registers, and Result Codes Basic AT Commands Speaker always on AT Commands, S-Registers, and Result Codes DSR always on MT5634ZLX/FE Terse Verbose Description Result CodesRegisters MT5634ZLX/FE Upstream data rates MT5634ZLX/FE Remote Configuration Basic Procedure SetupChanging the Setup Password Changing the Remote Escape Character Remote ConfigurationMT5634ZLX/FE Troubleshooting Modem Does Not Auto-Answer the Phone Modem Goes Off-Hook and Disables the Telephone LineModem Loses the Connection When in Use Troubleshooting Characters on the Screen Are DoubledNo Text Appears on the Screen in Data Mode No Text Appears on the Screen When in Command ModeOccasionally, the Modem Gives a Burst of Errors Modem Gets Random Errors in Transmitted DataModem Does Not Connect with Another Modem Select Properties Select Drivers in Properties TroubleshootingInstalling The Win 95 Driver Over SystemSoft CardWorks Enabling The MT5634ZLX/FEHighlight the folder MultiMobile-MT5634ZLX-FE-XXXX COM Port and IRQ ConflictsWindows Select HkeylocalmachineTroubleshooting Windows Windows NT 3.51 and NTAdditional References MultiMobile User Guide Appendices Appendix a Regulatory Compliance Class B Statement FCC PartIndustry Canada Appendices FCC Part 68 TelecomCanadian Limitations Notice FAX Branding StatementEMC, Safety and Terminal Directive Compliance Commission Decision CTR21New Zealand Telecom Warning Notice Troubleshooting Appendix B V.90 SupportIntroduction Lmndisnif Drivername LMNDIS$ Appendix C Comprehensive Driver Notes IntroductionNDIS2 Driver for Windows for Workgroups ODI Driver for Workgroups Appendix D Warranty, Service, and Technical Support Limited WarrantyOnline Warranty Registration If you don’t know the file name Technical SupportMulti-Tech BBS If you know the file nameAbout the Internet About the MultiMobile SoftGSM Cellular UpgradeSupplyNet Online Ordering Instructions About Ordering AccessoriesAppendix E Uninstalling in Windows 95/98 Index IndexMultiMobileUSB User Guide