Multi-Tech Systems MT5600DSVD manual Mount the Feet, Change the Speaker Jumper, Opening the Modem

Page 12

MultiModemDSVD User Guide

2 Installation

Step 1: Mount the Feet

The modem comes with a strip of self-adhesive plastic feet, which you can optional- ly mount on the bottom of the modem. To install the feet, simply peel them from their paper strip and press them into the recesses on the bottom of the modem.

Figure 2-1. Mounting the feet.

Step 2: Change the Speaker Jumper

This step is required only if you intend to connect a monophonic speaker to your modem. (This step is not required for stereo speakers or for the included headset.) If you do not intend to connect a monophonic speaker to your modem, skip to Step 3.

Warning: The following procedure must be performed by authorized service personnel.

Caution: The circuit board can be harmed by static electricity. Before you open the case, touch a grounded object, such as the metal chassis of your computer, to discharge any static electricity in your body, then touch the metal shell of the modem’s RS232 connector to ensure that there is no voltage difference between you and the modem.

Opening the Modem

1.If the modem is connected, turn it off and remove all connecting cables, including power and line cables.

2.Turn the modem over.

3.On the bottom of the modem are two screws that hold the case together. Remove both screws and set them aside.

4.Turn the modem over again.

5.Remove the top part of the modem case.

6.To close the modem, reverse steps 1–5.

7

Image 12

Contents Page Record of Revisions Introduction AT Commands, S-Registers & Result Codes Appendix E Upgrading the Modem Introduction Features IntroductionProduct Description Data What Is in Your Modem Package? Related ManualsInstallation Safety Warnings What You Will NeedWe supply You supplyMount the Feet Change the Speaker JumperOpening the Modem Changing the Speaker Jumper Location of speaker jumperConnect the Modem to Your System RS232 ConnectionLine Connection Power Connection Power-On TestPhone Connection Microphone ConnectionInstall the Modem Driver Installing the Modem DriverRemoving Your Old Modem Driver Install and Configure Your Software Operation Front Panel Configuring the Modem Connecting to the InternetTo install and run Dial-Up Networking in Windows 95 or To dial your Internet access providerDial-Up Networking Dial-Up Networking in Windows 95/98To install Dial-Up Networking Dial-Up Networking in Windows MeDial-Up Networking in Windows NT Select Start Settings Network and Dial-up Connections Dial-Up Networking in WindowsTo Originate a Voice Call in Speakerphone Mode Fax OperationVoice Operation To Answer a Voice Call in Speakerphone Mode To Originate a Dsvd Call Using the HeadsetTo Answer a Dsvd Call Using the Headset References AT Commands Registers Result Codes AT Commands AT Command Summary Echo Command Mode Characters DS=y Dial Stored Telephone NumberHook Control Information RequestMonitor Speaker Volume Monitor Speaker ModeDisplay Legacy Parameters Modulation HandshakeReturn Online to Data Mode Result Codes Enable/DisablePulse Dialing Select RegisterModem Reset Connect Message ControlResult Code Selection Long Space DisconnectError Correction Modes Data Carrier Detect DCD ControlData Terminal Ready DTR Control Modem-Initiated Flow ControlLoad Factory Settings 42bis Data Compression22bis Guard Tone Control Telephone Jack ControlCommunications Mode Asynchronous Communications ModeTest Commands Pulse Dial Make/Break RatioDisplay Current Configuration Store Current ConfigurationSelect Profile for Hard Reset Display Last Connection StatisticsLine Signal Level Line Signal QualityZy=x Store Telephone Number Data Compression ControlPCM Code Selection \An Maximum MNP Block Size\Bn Transmit Break \Kn Break Control\Nn Error Correction Mode Selection \Vn Single Line Connect MessageModulation Selection SubparametersMNP Extended Services Command #CID=n Caller ID Distinctive Ring ControlFlash Memory Download Voice Commands Command $SBn Serial Port Baud RateCommand +++ATCR Escape Sequence Command -SMS=nData/DSVD ModeDsvd Enable/Disable Command #BDR=n Baud Rate SelectCommand #CLS=n Data, Fax, or Voice/Audio Select Command #MDL? Identify ModelRegister Unit Range Default Description RegistersS32 S37 Register Unit Range Default Description S86 Result Codes Terse Verbose DescriptionProtocol ALT +FCERROR Solving Problems None of the Indicators Light Modem Does Not Respond to Commands LightModem Dials But Cannot Connect Modem4Disconnects While Online Modem4Cannot Connect When Answering File Transfer4Is Slower Than It Should BeData Is Being Lost There Are Garbage4 Characters on the Monitor Modem4Doesn’t Work with Caller IDFax and Data4Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFCC Part Industry CanadaFax Branding Statement Canadian Limitations NoticeEMC, Safety, and R&TTE Directive Compliance International Modem RestrictionsNew Zealand Telecom Warning Notice South African Notice Appendix B Technical Specifications MultiModemDSVD User Guide Technical Specifications Voice Compression Test procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testMultiModemDSVD User Guide Loopback Tests Limited Warranty Online Warranty RegistrationService North American ProductsTechnical Support International ProductsOrdering Accessories Internet SitesUpgrade Overview Identify the Modem FirmwareDownload the Upgrade File Extract the Upgrade FilesIdentify the Current Firmware Version Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersIndex MultiModemDSVD User Guide Index MultiModemDSVD User Guide Index MultiModemDSVD User Guide Index