Multi-Tech Systems MT5600DSVD Connect the Modem to Your System, RS232 Connection, Line Connection

Page 14

MultiModemDSVD User Guide

2 Installation

Step 3: Connect the Modem to Your System

Placing the modem in a convenient location, connect it to your computer’s serial port, to the telephone line, to AC power, and, optionally, to your telephone. For voice operations, connect it to the supplied headset or, optionally, to a microphone and a speaker or sound card.

Note: Do not turn on the modem until you have made all the connections.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

 

RS232

 

 

 

PHONE LINE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 2-3. Modem connections.

RS232 Connection

Plug one end of the serial cable into the RS232 connector on the modem, and the oth- er end into a serial port connector on your computer, such as COM1 or COM2.

Line Connection

Plug one end of the phone cable into the modem’s LINE jack, and the other end into a phone line wall jack.

Note: The LINE jack is not interchangeable with the PHONE jack. Do not plug the phone into the LINE jack or the line cable into the PHONE jack.

9

Image 14
Contents Page Record of Revisions Introduction AT Commands, S-Registers & Result Codes Appendix E Upgrading the Modem Introduction Product Description FeaturesIntroduction Data What Is in Your Modem Package? Related ManualsInstallation We supply Safety WarningsWhat You Will Need You supplyOpening the Modem Mount the FeetChange the Speaker Jumper Changing the Speaker Jumper Location of speaker jumperLine Connection Connect the Modem to Your SystemRS232 Connection Phone Connection Power ConnectionPower-On Test Microphone ConnectionRemoving Your Old Modem Driver Install the Modem DriverInstalling the Modem Driver Install and Configure Your Software Operation Front Panel Configuring the Modem Connecting to the InternetDial-Up Networking To install and run Dial-Up Networking in Windows 95 orTo dial your Internet access provider Dial-Up Networking in Windows 95/98Dial-Up Networking in Windows NT To install Dial-Up NetworkingDial-Up Networking in Windows Me Select Start Settings Network and Dial-up Connections Dial-Up Networking in WindowsVoice Operation To Originate a Voice Call in Speakerphone ModeFax Operation To Answer a Dsvd Call Using the Headset To Answer a Voice Call in Speakerphone ModeTo Originate a Dsvd Call Using the Headset References AT Commands Registers Result Codes AT Commands AT Command Summary Hook Control Echo Command Mode CharactersDS=y Dial Stored Telephone Number Information RequestDisplay Legacy Parameters Monitor Speaker VolumeMonitor Speaker Mode Modulation HandshakePulse Dialing Return Online to Data ModeResult Codes Enable/Disable Select RegisterResult Code Selection Modem ResetConnect Message Control Long Space DisconnectData Terminal Ready DTR Control Error Correction ModesData Carrier Detect DCD Control Modem-Initiated Flow Control22bis Guard Tone Control Load Factory Settings42bis Data Compression Telephone Jack ControlTest Commands Communications ModeAsynchronous Communications Mode Pulse Dial Make/Break RatioSelect Profile for Hard Reset Display Current ConfigurationStore Current Configuration Display Last Connection StatisticsZy=x Store Telephone Number Line Signal LevelLine Signal Quality Data Compression Control\Bn Transmit Break PCM Code Selection\An Maximum MNP Block Size \Kn Break Control\Nn Error Correction Mode Selection \Vn Single Line Connect MessageModulation Selection SubparametersMNP Extended Services Flash Memory Download Command #CID=n Caller IDDistinctive Ring Control Command +++ATCR Escape Sequence Voice CommandsCommand $SBn Serial Port Baud Rate Command -SMS=nData/DSVD ModeCommand #CLS=n Data, Fax, or Voice/Audio Select Dsvd Enable/DisableCommand #BDR=n Baud Rate Select Command #MDL? Identify ModelRegister Unit Range Default Description RegistersS32 S37 Register Unit Range Default Description S86 Result Codes Terse Verbose DescriptionProtocol ALT +FCERROR Solving Problems None of the Indicators Light Modem Does Not Respond to Commands LightModem Dials But Cannot Connect Modem4Disconnects While Online Data Is Being Lost Modem4Cannot Connect When AnsweringFile Transfer4Is Slower Than It Should Be Fax and Data4Software Can’t Run at the Same Time There Are Garbage4 Characters on the MonitorModem4Doesn’t Work with Caller ID Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFCC Part Industry CanadaFax Branding Statement Canadian Limitations NoticeNew Zealand Telecom Warning Notice EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions South African Notice Appendix B Technical Specifications MultiModemDSVD User Guide Technical Specifications Voice Compression Test procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testMultiModemDSVD User Guide Loopback Tests Service Limited WarrantyOnline Warranty Registration North American ProductsTechnical Support International ProductsOrdering Accessories Internet SitesUpgrade Overview Identify the Modem FirmwareIdentify the Current Firmware Version Download the Upgrade FileExtract the Upgrade Files Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersIndex MultiModemDSVD User Guide Index MultiModemDSVD User Guide Index MultiModemDSVD User Guide Index