Multi-Tech Systems MT5634ZBA-DID manual Value Speed, Value Rate

Page 37

MultiModemDID User Guide			Chapter 4 - AT Commands, S-Registers, Result Codes

S36	decimal	0–7	7	Specifies the action to take in the event of a
				negotiation failure when error control is
				selected. (See S48.)
S37	decimal	0–19	0	Sets the maximum V.34 “upstream” speed
				at which the modem attempts to connect.
				Value Speed

0	maximum modem speed
1	reserved
2	1200/75 bps
3	300 bps
4	reserved
5	1200 bps
6	2400 bps
7	4800 bps
8	7200 bps
9	9600 bps
10	12000 bps
11	14400 bps
12	16800 bps
13	19200 bps
14	21600 bps
15	24000 bps
16	26400 bps
17	28800 bps
18	31200 bps
19	33600 bps

S38	decimal 0–23	1	Sets the maximum 56K “downstream” speed
			at which the modem attempts to connect.
			The default maximum speed is 56K bps.
			Note: When using V.34 or V.32 client-to-client
			connections in poor conditions, setting
			S38=0 may result in better performance.
			Value	Rate
			0	56K disabled
			1	56K autorate
			2	28000 bps
			3	29333 bps
			4	30666 bps
			5	32000 bps
			6	33333 bps
			7	34666 bps
			8	36000 bps
			9	37333 bps
			10	38666 bps
			11	40000 bps
			12	41333 bps
			13	42666 bps
			14	44000 bps
			15	45333 bps
			16	46666 bps

37

Image 37

Contents User Guide Revision Date Description Record of RevisionsTrademarks PatentsTable of Contents MultiModemDID User Guide Contents Introduction and Description FeaturesIntroduction We Supply SafetyYou Supply Assemble the Modem InstallationConnect the Modem to Your System Removing Your Old Modem from Windows Connect the Modem to the AC Power OutletFrom Windows 2000, XP Front Panel of the MultiModemDID Modem OperationOperation Did OperationDial-Up Networking Connecting to the InternetAT Commands, S -Registers Result Codes Repeat Last Command AT CommandsCommunication Standard Setting AnswerNumber ATDT1028806127853500$123456789 Echo Command Mode CharactersDS=n Dial Stored Telephone Number Echo Online Data CharactersReturn Online to Data Mode Monitor Speaker ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetResult Code Format Result Code OptionsAsynchronous Communications Mode Load Factory SettingsData Terminal Ready DTR Control XON/XOFF Pacing ControlDisplay Current Settings Test CommandsStore Current Configuration Store Dialing Command\Bn Transmit Break Online command mode. The modem receives a \Bn\Kn Break Control \Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection \Vn Protocol Result CodeDC n AT Command Control Adaptive Answer Result Code EnableDirect Connect Enable View Numbers in BlacklistCommand Speed Response Cisco ConfigurationCommand +DCS=x,y Select V.44 Data Compression $Dn DTR DialingData Compression Reporting Command +DS44=n V.44 Data CompressionEnable Synchronous Buffered Mode Subparameters Modulation SelectionMod value Valid max-rate values bps Command +PCW=n Call Waiting Enable CommandsModem on Hold Enable PCM Upstream IgnoreCommand +PMHT=n Modem on Hold Timer Command +PMHR=n Modem on Hold InitiateCommand +VCID=n Caller ID Selection Other CommandsCommand +VDR= x, y Distinctive Ring Report Quick Connect ControlCommand %%%ATCR Remote Configuration Escape Sequence Command +++ATCR Escape SequenceMT5634ZBA-DID Initialization Recommendations Wait for Digit Time-Out Time Busy-Out Timer at End of CallNumber of did Digits Expected Digit FormatDF0 Format for Reporting Incoming did NumberDF1 DF2Page Registers Register Unit Range Default DescriptionValue Rate Value SpeedValue Digital loss S42Ring signal detected Command executedCarrier signal lost or not detected Invalid commandPage Basic Procedure Remote ConfigurationSetup Changing the Remote Escape Character None of the Indicators Light TroubleshootingModem Does Not Respond to Commands Modem Dials But Cannot Connect Modem Disconnects While Online Modem Cannot Connect When AnsweringModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeDid Troubleshooting FCC Part 68 Telecom Appendix a Regulatory ComplianceFax Branding Statement FCC PartCanadian Limitations Notice Industry CanadaFax Appendix B Technical SpecificationsAppendix C Upgrading the Modem’s Firmware Upgrade OverviewExtract the Upgrade Files Installation Appendix D Installing a Modem Under LinuxSelect Dialup Configuration Tool Standard Linux Serial Port DefinitionsSelect RH PPP Dialer Calling the ISPIndex SymbolsMultiModemDID User Guide Index MultiModemDID User Guide Index