Multi-Tech Systems MT5634ZBA-DID Command executed, Modem connected to line, Ring signal detected

Page 39

MultiModemDID User Guide

Chapter 4 - AT Commands, S-Registers, Result Codes

 

 

Result Codes

In command mode your modem can send responses called result codes to your computer. Result codes are used by communications programs and can also appear on your monitor.

Terse

Verbose

Description

0

OK

Command executed

1

CONNECT

Modem connected to line

2

RING

Ring signal detected

3

NO CARRIER

Carrier signal lost or not detected

4

ERROR

Invalid command

5

CONNECT 1200 *

Connected at 1200 bps

6

NO DIALTONE

No dial tone detected

7

BUSY

Busy signal detected

8

NO ANSWER

No answer at remote end

10

CONNECT 2400 *

Connected at 2400 bps

11

CONNECT 4800 *

Connected at 4800 bps

12

CONNECT 9600 *

Connected at 9600 bps

13CONNECT 14400 * Connected at 14400 bps

14CONNECT 19200 * Connected at 19200 bps

24

CONNECT 7200 *

Connected at 7200 bps

25CONNECT 12000 * Connected at 12000 bps

26CONNECT 16800 * Connected at 16800 bps

40

CONNECT 300 *

Connected at 300 bps

55CONNECT 21600 * Connected at 21600 bps

56CONNECT 24000 * Connected at 24000 bps

57CONNECT 26400 * Connected at 26400 bps

58CONNECT 28800 * Connected at 28800 bps

59CONNECT 31200 * Connected at 31200 bps

60CONNECT 33600 * Connected at 33600 bps

70CONNECT 32000 * Connected at 32000 bps, 56K rate

71CONNECT 34000 * Connected at 34000 bps, 56K rate

72CONNECT 36000 * Connected at 36000 bps, 56K rate

73CONNECT 38000 * Connected at 38000 bps, 56K rate

74CONNECT 40000 * Connected at 40000 bps, 56K rate

75CONNECT 42000 * Connected at 42000 bps, 56K rate

76CONNECT 44000 * Connected at 44000 bps, 56K rate

77CONNECT 46000 * Connected at 46000 bps, 56K rate

78CONNECT 48000 * Connected at 48000 bps, 56K rate

79CONNECT 50000 * Connected at 50000 bps, 56K rate

80CONNECT 52000 * Connected at 52000 bps, 56K rate

81CONNECT 54000 * Connected at 54000 bps, 56K rate

82CONNECT 56000 * Connected at 56000 bps, 56K rate

88

DELAYED

Delay is in effect for the dialed number

89

BLACKLISTED

Dialed number is blacklisted

90

BLACKLIST FULL

Blacklist is full

*When the extended result code configuration option is enabled, one of the following codes is appended to the result code, depending on the type of error control connection:

V42bis – V.42 error control (LAP-M) and V.42bis data compression V42 – V.42 error control (LAP-M) only

MNP5 – MNP 4 error control and MNP 5 data compression MNP4 – MNP 4 error control only

NoEC – No error control protocol

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents User Guide Patents Record of RevisionsRevision Date Description TrademarksTable of Contents MultiModemDID User Guide Contents Features Introduction and DescriptionIntroduction Safety We SupplyYou Supply Installation Assemble the ModemConnect the Modem to Your System Removing Your Old Modem from Windows Connect the Modem to the AC Power OutletFrom Windows 2000, XP Front Panel of the MultiModemDID Modem OperationOperation Did OperationDial-Up Networking Connecting to the InternetAT Commands, S -Registers Result Codes Answer AT CommandsRepeat Last Command Communication Standard SettingEcho Online Data Characters Echo Command Mode CharactersNumber ATDT1028806127853500$123456789 DS=n Dial Stored Telephone NumberModulation Handshake Monitor Speaker ModeReturn Online to Data Mode Result Codes Enable/DisableResult Code Options Modem ResetTone Dialing Result Code FormatXON/XOFF Pacing Control Load Factory SettingsAsynchronous Communications Mode Data Terminal Ready DTR ControlStore Dialing Command Test CommandsDisplay Current Settings Store Current ConfigurationOnline command mode. The modem receives a \Bn \Bn Transmit Break\Kn Break Control \Vn Protocol Result Code \Nn Error Correction Mode Selection\Tn Inactivity Timer \Qn Flow Control SelectionView Numbers in Blacklist Adaptive Answer Result Code EnableDC n AT Command Control Direct Connect Enable$Dn DTR Dialing Cisco ConfigurationCommand Speed Response Command +DCS=x,y Select V.44 Data CompressionData Compression Reporting Command +DS44=n V.44 Data CompressionEnable Synchronous Buffered Mode Subparameters Modulation SelectionMod value Valid max-rate values bps PCM Upstream Ignore CommandsCommand +PCW=n Call Waiting Enable Modem on Hold EnableCommand +PMHT=n Modem on Hold Timer Command +PMHR=n Modem on Hold InitiateQuick Connect Control Other CommandsCommand +VCID=n Caller ID Selection Command +VDR= x, y Distinctive Ring ReportCommand %%%ATCR Remote Configuration Escape Sequence Command +++ATCR Escape SequenceMT5634ZBA-DID Initialization Recommendations Digit Format Busy-Out Timer at End of CallWait for Digit Time-Out Time Number of did Digits ExpectedDF2 Format for Reporting Incoming did NumberDF0 DF1Page Registers Register Unit Range Default DescriptionValue Rate Value SpeedValue Digital loss S42Invalid command Command executedRing signal detected Carrier signal lost or not detectedPage Remote Configuration Basic ProcedureSetup Changing the Remote Escape Character Troubleshooting None of the Indicators LightModem Does Not Respond to Commands Modem Dials But Cannot Connect Fax and Data Software Can’t Run at the Same Time Modem Cannot Connect When AnsweringModem Disconnects While Online Modem Doesn’t Work with Caller IDDid Troubleshooting FCC Part 68 Telecom Appendix a Regulatory ComplianceIndustry Canada FCC PartFax Branding Statement Canadian Limitations NoticeFax Appendix B Technical SpecificationsAppendix C Upgrading the Modem’s Firmware Upgrade OverviewExtract the Upgrade Files Standard Linux Serial Port Definitions Appendix D Installing a Modem Under LinuxInstallation Select Dialup Configuration ToolSelect RH PPP Dialer Calling the ISPIndex SymbolsMultiModemDID User Guide Index MultiModemDID User Guide Index
Top Page Image Contents