Multi-Tech Systems MT5634ZBA-DID manual Command +++ATCR Escape Sequence

Page 31

MultiModemDID User Guide	Chapter 4 - AT Commands, S-Registers, Result Codes

Escape Commands

Command: +++AT<CR> Escape Sequence

Values:	n/a
Description:	Puts the modem in command mode (and optionally issues a
	command) while remaining online. Type +++AT and up to six
	command characters, then press ENTER. Used mostly to issue
	the hang-up command: +++ATH<CR>.
Command: %%%AT<CR> Remote Configuration Escape Sequence
Values:	n/a
Description:	Initiates remote configuration mode while online with remote
	modem. The remote configuration escape character (%) is de-
	fined in register S13.

Image 31

Contents User Guide Patents Record of RevisionsRevision Date Description TrademarksTable of Contents MultiModemDID User Guide Contents Introduction and Description FeaturesIntroduction We Supply SafetyYou Supply Assemble the Modem InstallationConnect the Modem to Your System Removing Your Old Modem from Windows Connect the Modem to the AC Power OutletFrom Windows 2000, XP Front Panel of the MultiModemDID Modem OperationOperation Did OperationDial-Up Networking Connecting to the InternetAT Commands, S -Registers Result Codes Answer AT CommandsRepeat Last Command Communication Standard SettingEcho Online Data Characters Echo Command Mode CharactersNumber ATDT1028806127853500$123456789 DS=n Dial Stored Telephone NumberModulation Handshake Monitor Speaker ModeReturn Online to Data Mode Result Codes Enable/DisableResult Code Options Modem ResetTone Dialing Result Code FormatXON/XOFF Pacing Control Load Factory SettingsAsynchronous Communications Mode Data Terminal Ready DTR ControlStore Dialing Command Test CommandsDisplay Current Settings Store Current Configuration\Bn Transmit Break Online command mode. The modem receives a \Bn\Kn Break Control \Vn Protocol Result Code \Nn Error Correction Mode Selection\Tn Inactivity Timer \Qn Flow Control SelectionView Numbers in Blacklist Adaptive Answer Result Code EnableDC n AT Command Control Direct Connect Enable$Dn DTR Dialing Cisco ConfigurationCommand Speed Response Command +DCS=x,y Select V.44 Data CompressionData Compression Reporting Command +DS44=n V.44 Data CompressionEnable Synchronous Buffered Mode Subparameters Modulation SelectionMod value Valid max-rate values bps PCM Upstream Ignore CommandsCommand +PCW=n Call Waiting Enable Modem on Hold EnableCommand +PMHT=n Modem on Hold Timer Command +PMHR=n Modem on Hold InitiateQuick Connect Control Other CommandsCommand +VCID=n Caller ID Selection Command +VDR= x, y Distinctive Ring ReportCommand %%%ATCR Remote Configuration Escape Sequence Command +++ATCR Escape SequenceMT5634ZBA-DID Initialization Recommendations Digit Format Busy-Out Timer at End of CallWait for Digit Time-Out Time Number of did Digits ExpectedDF2 Format for Reporting Incoming did NumberDF0 DF1Page Registers Register Unit Range Default DescriptionValue Rate Value SpeedValue Digital loss S42Invalid command Command executedRing signal detected Carrier signal lost or not detectedPage Basic Procedure Remote ConfigurationSetup Changing the Remote Escape Character None of the Indicators Light TroubleshootingModem Does Not Respond to Commands Modem Dials But Cannot Connect Fax and Data Software Can’t Run at the Same Time Modem Cannot Connect When AnsweringModem Disconnects While Online Modem Doesn’t Work with Caller IDDid Troubleshooting FCC Part 68 Telecom Appendix a Regulatory ComplianceIndustry Canada FCC PartFax Branding Statement Canadian Limitations NoticeFax Appendix B Technical SpecificationsAppendix C Upgrading the Modem’s Firmware Upgrade OverviewExtract the Upgrade Files Standard Linux Serial Port Definitions Appendix D Installing a Modem Under LinuxInstallation Select Dialup Configuration ToolSelect RH PPP Dialer Calling the ISPIndex SymbolsMultiModemDID User Guide Index MultiModemDID User Guide Index

Escape Commands

Command: +++AT<CR> Escape Sequence

Command: %%%AT<CR> Remote Configuration Escape Sequence