Multi-Tech Systems MT5634ZBA-DID manual From Windows 2000, XP

Page 9

MultiModemDID User Guide	Chapter 2 - Installation

From Windows 2000, XP

1.Click Start Settings Control Panel.

2.Double-click the Phone and Modems icon and click on the Modems tab.

3.In the list box, select the old modem.

4.Click Remove, then click Close.

5.The next time you dial a HyperTerminal connection, it will select your new modem and ask you to confirm the selection.

From Windows 98, Me

1.Click Start Settings Control Panel.

2.Double-click the Modems icon to open the Modems Properties sheet.

3.In the list box, select the old modem.

4.Click Remove, then click Close.

5.The next time you dial a HyperTerminal connection, it will select your new modem and ask you to confirm the selection.

Image 9

Contents User Guide Revision Date Description Record of RevisionsTrademarks PatentsTable of Contents MultiModemDID User Guide Contents Features Introduction and DescriptionIntroduction Safety We SupplyYou Supply Installation Assemble the ModemConnect the Modem to Your System Removing Your Old Modem from Windows Connect the Modem to the AC Power OutletFrom Windows 2000, XP Front Panel of the MultiModemDID Modem OperationOperation Did OperationDial-Up Networking Connecting to the InternetAT Commands, S -Registers Result Codes Repeat Last Command AT CommandsCommunication Standard Setting AnswerNumber ATDT1028806127853500$123456789 Echo Command Mode CharactersDS=n Dial Stored Telephone Number Echo Online Data CharactersReturn Online to Data Mode Monitor Speaker ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetResult Code Format Result Code OptionsAsynchronous Communications Mode Load Factory SettingsData Terminal Ready DTR Control XON/XOFF Pacing ControlDisplay Current Settings Test CommandsStore Current Configuration Store Dialing CommandOnline command mode. The modem receives a \Bn \Bn Transmit Break\Kn Break Control \Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection \Vn Protocol Result CodeDC n AT Command Control Adaptive Answer Result Code EnableDirect Connect Enable View Numbers in BlacklistCommand Speed Response Cisco ConfigurationCommand +DCS=x,y Select V.44 Data Compression $Dn DTR DialingData Compression Reporting Command +DS44=n V.44 Data CompressionEnable Synchronous Buffered Mode Subparameters Modulation SelectionMod value Valid max-rate values bps Command +PCW=n Call Waiting Enable CommandsModem on Hold Enable PCM Upstream IgnoreCommand +PMHT=n Modem on Hold Timer Command +PMHR=n Modem on Hold InitiateCommand +VCID=n Caller ID Selection Other CommandsCommand +VDR= x, y Distinctive Ring Report Quick Connect ControlCommand %%%ATCR Remote Configuration Escape Sequence Command +++ATCR Escape SequenceMT5634ZBA-DID Initialization Recommendations Wait for Digit Time-Out Time Busy-Out Timer at End of CallNumber of did Digits Expected Digit FormatDF0 Format for Reporting Incoming did NumberDF1 DF2Page Registers Register Unit Range Default DescriptionValue Rate Value SpeedValue Digital loss S42Ring signal detected Command executedCarrier signal lost or not detected Invalid commandPage Remote Configuration Basic ProcedureSetup Changing the Remote Escape Character Troubleshooting None of the Indicators LightModem Does Not Respond to Commands Modem Dials But Cannot Connect Modem Disconnects While Online Modem Cannot Connect When AnsweringModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeDid Troubleshooting FCC Part 68 Telecom Appendix a Regulatory ComplianceFax Branding Statement FCC PartCanadian Limitations Notice Industry CanadaFax Appendix B Technical SpecificationsAppendix C Upgrading the Modem’s Firmware Upgrade OverviewExtract the Upgrade Files Installation Appendix D Installing a Modem Under LinuxSelect Dialup Configuration Tool Standard Linux Serial Port DefinitionsSelect RH PPP Dialer Calling the ISPIndex SymbolsMultiModemDID User Guide Index MultiModemDID User Guide Index