Multi-Tech Systems MT5634ZBA-DID manual Appendix B Technical Specifications, Fax

Page 49

MultiModemDID User Guide	Appendix B – Technical Specifications

Appendix B – Technical Specifications

Your MultiModemZBA-DID fax modem meets the following specifications:

Trade Name	MultiModem™
Model Number	MT5634ZBA-DID
Fax
Standards:	Super G3 V.34/33.6K bps; V.17/14.4Kbps, V.29, V.27ter, V.21, T.30,
	T.30 Annex A, T.30 Annex F, T.31, T.31 Annex B, T.32 Annex C,
	TR29.2 Class 2 Recommendation
Rates:	33.6K, 31.2K, 28.8K, 26.4K, 24K, 21.6K, 19.2K, 16.8K, 14.4K, 12K,
	9600, 7200, 4800, 2400, 300 bps
Error Correction:	V.42, ECM
Compression:	MH (T.4), MR (T.4), & MMR (T.6)
Conversion:	Real time (on-the-fly) compression conversion
Commands:	Class 1, 2, 1.0, 2.0, 2.1
Service Types:	Wink-start; immediate-start; delay dial
Signaling Types:	DTMF (1-7 digits accepted)
Data
Rates:	V.92/56K, V.90/56K, enhanced V.34/33.6K & others
Error Correction:	V.42 & MNP®
Data Compression:	V.44, V.42bis, MNP® Class 5
Physical Description	4.3" w × 1.0" h × 5.7" d; 8 oz
	(10.9 cm × 2.5 cm × 14.5 cm; 227g)
Weight	224 g (8 oz)
Approvals	EMC: FCC Part 15 Class B
	Safety: UL, cUL, UL60950
	Telecom: FCC Part 68, CS03
Modem Compatibility	56K; ITU-T V.34 enhanced, V.34, V.32terbo, V.32bis, V.32, V.22bis,
	V.22; Bell 212A and 103/113; ITU-T V.29, V.42, V.42bis; ITU-T V.21 &
	V.23 in international versions
Fax Compatibility	ITU-T Group 3, Class 1 and 2, T.4, T.30, V.21, V.27ter, V.29, V.17, and
	TIA/EIA TR29.2
Flow Control	XON/XOFF (software), RTS/CTS (hardware)
Command Buffer	40 characters
Frequency Stability	±0.01%
Receiver Sensitivity	-43 dBm under worst-case conditions
AGC Dynamic Range	43 dB
Cables	Two RJ-11s (LINE jack and PHONE jack)
	One RJ-12 (DID line)
	One DB9 (serial port)
	Note: Any cables connected to the computer should be shielded to
	reduce interference.
Environmental	Temperature range 0°–50°C (32°–120°F); humidity range 20–90%
	(non-condensing)
Limited Warranty	2 years

49

Image 49

Contents User Guide Revision Date Description Record of RevisionsTrademarks PatentsTable of Contents MultiModemDID User Guide Contents Introduction and Description FeaturesIntroduction We Supply SafetyYou Supply Assemble the Modem InstallationConnect the Modem to Your System Removing Your Old Modem from Windows Connect the Modem to the AC Power OutletFrom Windows 2000, XP Front Panel of the MultiModemDID Modem OperationOperation Did OperationDial-Up Networking Connecting to the InternetAT Commands, S -Registers Result Codes Repeat Last Command AT CommandsCommunication Standard Setting AnswerNumber ATDT1028806127853500$123456789 Echo Command Mode CharactersDS=n Dial Stored Telephone Number Echo Online Data CharactersReturn Online to Data Mode Monitor Speaker ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetResult Code Format Result Code OptionsAsynchronous Communications Mode Load Factory SettingsData Terminal Ready DTR Control XON/XOFF Pacing ControlDisplay Current Settings Test CommandsStore Current Configuration Store Dialing Command\Bn Transmit Break Online command mode. The modem receives a \Bn\Kn Break Control \Tn Inactivity Timer \Nn Error Correction Mode Selection\Qn Flow Control Selection \Vn Protocol Result CodeDC n AT Command Control Adaptive Answer Result Code EnableDirect Connect Enable View Numbers in BlacklistCommand Speed Response Cisco ConfigurationCommand +DCS=x,y Select V.44 Data Compression $Dn DTR DialingData Compression Reporting Command +DS44=n V.44 Data CompressionEnable Synchronous Buffered Mode Subparameters Modulation SelectionMod value Valid max-rate values bps Command +PCW=n Call Waiting Enable CommandsModem on Hold Enable PCM Upstream IgnoreCommand +PMHT=n Modem on Hold Timer Command +PMHR=n Modem on Hold InitiateCommand +VCID=n Caller ID Selection Other CommandsCommand +VDR= x, y Distinctive Ring Report Quick Connect ControlCommand %%%ATCR Remote Configuration Escape Sequence Command +++ATCR Escape SequenceMT5634ZBA-DID Initialization Recommendations Wait for Digit Time-Out Time Busy-Out Timer at End of CallNumber of did Digits Expected Digit FormatDF0 Format for Reporting Incoming did NumberDF1 DF2Page Registers Register Unit Range Default DescriptionValue Rate Value SpeedValue Digital loss S42Ring signal detected Command executedCarrier signal lost or not detected Invalid commandPage Basic Procedure Remote ConfigurationSetup Changing the Remote Escape Character None of the Indicators Light TroubleshootingModem Does Not Respond to Commands Modem Dials But Cannot Connect Modem Disconnects While Online Modem Cannot Connect When AnsweringModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeDid Troubleshooting FCC Part 68 Telecom Appendix a Regulatory ComplianceFax Branding Statement FCC PartCanadian Limitations Notice Industry CanadaFax Appendix B Technical SpecificationsAppendix C Upgrading the Modem’s Firmware Upgrade OverviewExtract the Upgrade Files Installation Appendix D Installing a Modem Under LinuxSelect Dialup Configuration Tool Standard Linux Serial Port DefinitionsSelect RH PPP Dialer Calling the ISPIndex SymbolsMultiModemDID User Guide Index MultiModemDID User Guide Index