LSI SAS6160 manual Rack. These options are shown in the following figure

Page 25

LSISAS6160 SAS Switch User Guide

Chapter 2: Installation and Hardware Setup Installing the SAS6160 Switch

2.3.1

Installing the SAS6160 Self

A special shelf is available for mounting one or two SAS6160 switches in a standard

 

 

rack. These options are shown in the following figure.

 

 

Figure 2: One or Two SAS6160 Switches on a Rack Mounted Shelf

To assemble and mount the shelf in a rack, follow these steps:

1.Unpack the SAS6160 shelf. Ensure that there is a shelf and two shelf rails along with eight screws and four clips.

2.Insert the two side rails from the back of the shelf, as shown in the following figure.

Figure 3: Inserting Side Rails into the Shelf

These rails allow adjustment of the shelf to fit different rack depths. Make sure the mounting ears on the rails are turned out as shown.

LSI Corporation September 2010

Page 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Chapter FeaturesLSISAS6160 Switch Serial Attached Scsi and the SAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch Link between Two Single SAS Phys SAS Phys, Ports, and ConnectorsNarrow and Wide SAS Ports Mini SAS 4x Cable SAS Connectors and CablingOnly the storage within its zone or zones Minimize conflictsAcross the entire Zpsds SAS Zoning OverviewFollowing figure shows a simple example of zoning Groups and zone sets manually by using the SDM utilityCreating SAS Zones Overview SAS Routing and Zoning Configuration for Zoning Example Creating Zone Groups Connecting Devices to the SAS6160 SwitchExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Identifying Switch Components Unpacking the SwitchTo interpret the LEDs on the switch Carton contains the following itemsSAS6160 Connectors Installing the SAS6160 SwitchCables SAS6160 LEDsRack. These options are shown in the following figure Mounting Shelf in a Rack Setting a Static IP Address Connecting to a Host Changing the Default Static IP AddressExit SDM-CLI and power cycle the switch Exit SDM-GUI and power cycle the switchUsing SDM-GUI For example1 FCC Connecting SAS and Sata Hardware Safety NoticesCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices Starting SDM-GUI SDM-GUI AccountsEmbedded SDM only supports a single domain OptionsFile, Server, and Help Menu Options Views Tab Information is available to both admin and user accountsFor zoning View End Device TableAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsThis section, click the hyperlinks on the Domain tab Domain TabNode100, and so on Alias ManagementDomain. You also can also this command to delete aliases View/Delete Aliases commandView/Delete Aliases Zone set and the two associated zone groups Connector WizardBox and clicking the Delete button Group to communicate with each otherMaximum number of 248, the wizard displays an error message Guide you through the configuration processCheck box and clicking the Delete button Zone group to communicate with each otherCreate Zone Group Manually Configure Zone Groups Create Zone GroupView Zone Group Time of activation. shows the View Zone Group windowModify Zone Group Delete Zone GroupBinary 0, as defined by the SAS 2.0 specification Maximum password length is 32 charactersPassword MatrixZone set View Zone Set windowView Zone Set Modify Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetDelete Zone Set Window and then clicking DeleteDevice Tree and Properties Tab Devices TabFollowing figure shows the Properties tab Selected device. In , the domain properties are shownProperties Tab Environmentals Tab Background loopFollowing figure shows the Attached Devices tab Those connectionsAttached Devices Tab Following figure shows the Phys tab Selected expanderZone Group Tab Zone Group TabSuccessful update This tab contains the following commandsUpdate Firmware Operations TabEnable/Disable/Reset Following figure shows the Enable/Disable/Reset windowReset Switch PhysAs shown in the following figures Configure IPCommand arguments Command Usage SyntaxHelp command SDM-CLI Commands„ help command Domain focus domain name„ passwd admin Passwd admin user„ passwd user Exit„ alias delete „ show phy „ show alias„ show zonegroup „ show zoneset„ zonegroup create name „ zonegroup add name sas addressaliasphy„ zonegroup delete single name „ zonegroup delete all noconfirm„ zoneset activate name Set membership„ zoneset add name zone group zone group „ zoneset create name„ zoneset passwd Sample Output for Show CommandSdmcli show alias Sdmcli show alias CalhounSdmcli show device Calhoun Sdmcli show phy Sdmcli show domainShow domain Show phySdmcli show phy Calhoun Alias Phy Device Capabilities SAS Address TypeRA Routing Attributes VP Virtual PHY Zone Grp Show phy aliasZoning Inactive * phy may be assigned to a zone group Zoning Active Zone Group NumberSdmcli show version Sdmcli show phy Lincoln01SDM-CLI Version SDM-D Version Show phy alias phySdmcli show zoneset active Sdmcli show zonegroup ZoneOne#001Show zoneset data name Sdmcli show zoneset data ZoneOne Show zonegroup nameXip -i 500062b15555557f get exp Xip -i get availTroubleshooting
Top Page Image Contents