LSI SAS6160 manual alias delete

Page 62

Chapter 4: SAS Domain Manager Command Line Interface SDM-CLI Commands

LSISAS6160 SAS Switch User Guide

		Usage:
			alias create <name> <sas address>
			Creates an alias that is bound to a specific device within the domain. The alias name
			can have a maximum of 24 characters. Valid characters are 0 through 9, A through Z,
			a through z, # (pound), - (dash), and _ (underscore). An alias name must not closely
			resemble a valid SAS address (16 hexadecimal characters that start with a 5).
		alias delete		single <name>
			Deletes a single specified alias.
		alias delete		all [noconfirm]
			Deletes all aliases. If you specify the [noconfirm] option, the deletion occurs
			immediately without an additional confirmation prompt. Otherwise, SDM first
			prompts you to confirm the action.
4.2.6	Device Command	(Intra-Domain) Use the device command to manage individual devices (LSI expanders)
		within the domain.
		Authority: Admin
		Syntax:
			device (<sas	address><alias>) reset [noconfirm]
			device (<sas	address><alias>):<phy> reset [counters]
			device (<sas	address><alias>):<phy> (disableenable)
			device (<sas	address><alias>) update <file> <ip address>
			device (<sas	address><alias>) ip (dhcpstatic <ip
			address> <mask> <gateway>)
			Configure IP	address for the switch.
		Usage:
			device (<sas	address><alias>) reset [noconfirm]
			Resets a device after user confirmation. If you specify the [noconfirm] option,
			the reset occurs immediately without an additional confirmation prompt.
			Otherwise, SDM first prompts you to confirm the action.
			device (<sas	address><alias>):<phy> reset
			Resets a phy.	address><alias>):<phy> reset counters
			device (<sas	address><alias>):<phy> reset counters
			Clears a phy’s counters.
			device (<sas	address><alias>):<phy> disable
			Disables a phy until the next device reset.
			device (<sas	address><alias>):<phy> enable
			Enables a previously disabled phy.
			device (<sas	address><alias>) update <file> <ip address>
			Installs a new firmware image on the specified device and automatically resets the
			device after a successful update. SDM checks to ensure that the product
			identification of the image matches the targeted device. The targeted device is
			responsible for any other image validation.

Page 62

LSI Corporation September 2010

Image 62

Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Features ChapterSerial Attached Scsi and the SAS6160 Switch LSISAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch SAS Phys, Ports, and Connectors Link between Two Single SAS PhysNarrow and Wide SAS Ports SAS Connectors and Cabling Mini SAS 4x CableAcross the entire Zpsds Minimize conflictsOnly the storage within its zone or zones SAS Zoning OverviewCreating SAS Zones Groups and zone sets manually by using the SDM utilityFollowing figure shows a simple example of zoning Overview SAS Routing and Zoning Configuration for Zoning Example Connecting Devices to the SAS6160 Switch Creating Zone GroupsExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration To interpret the LEDs on the switch Unpacking the SwitchIdentifying Switch Components Carton contains the following itemsCables Installing the SAS6160 SwitchSAS6160 Connectors SAS6160 LEDsRack. These options are shown in the following figure Mounting Shelf in a Rack Connecting to a Host Changing the Default Static IP Address Setting a Static IP AddressUsing SDM-GUI Exit SDM-GUI and power cycle the switchExit SDM-CLI and power cycle the switch For exampleConnecting SAS and Sata Hardware Safety Notices 1 FCCCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices SDM-GUI Accounts Starting SDM-GUIOptions Embedded SDM only supports a single domainFile, Server, and Help Menu Options For zoning Information is available to both admin and user accountsViews Tab View End Device TableAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsNode100, and so on Domain TabThis section, click the hyperlinks on the Domain tab Alias ManagementView/Delete Aliases View/Delete Aliases commandDomain. You also can also this command to delete aliases Box and clicking the Delete button Connector WizardZone set and the two associated zone groups Group to communicate with each otherCheck box and clicking the Delete button Guide you through the configuration processMaximum number of 248, the wizard displays an error message Zone group to communicate with each otherManually Configure Zone Groups Create Zone Group Create Zone GroupModify Zone Group Time of activation. shows the View Zone Group windowView Zone Group Delete Zone GroupPassword Maximum password length is 32 charactersBinary 0, as defined by the SAS 2.0 specification MatrixView Zone Set View Zone Set windowZone set Modify Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetWindow and then clicking Delete Delete Zone SetDevices Tab Device Tree and Properties TabProperties Tab Selected device. In , the domain properties are shownFollowing figure shows the Properties tab Background loop Environmentals TabAttached Devices Tab Those connectionsFollowing figure shows the Attached Devices tab Selected expander Following figure shows the Phys tabZone Group Tab Zone Group TabUpdate Firmware This tab contains the following commandsSuccessful update Operations TabReset Switch Following figure shows the Enable/Disable/Reset windowEnable/Disable/Reset PhysConfigure IP As shown in the following figuresCommand Usage Syntax Command arguments„ help command SDM-CLI CommandsHelp command Domain focus domain name„ passwd user Passwd admin user„ passwd admin Exit„ alias delete „ show zonegroup „ show alias„ show phy „ show zoneset„ zonegroup delete single name „ zonegroup add name sas addressaliasphy„ zonegroup create name „ zonegroup delete all noconfirm„ zoneset add name zone group zone group Set membership„ zoneset activate name „ zoneset create nameSdmcli show alias Sample Output for Show Command„ zoneset passwd Sdmcli show alias CalhounSdmcli show device Calhoun Show domain Sdmcli show domainSdmcli show phy Show phyRA Routing Attributes VP Virtual PHY Zone Grp Alias Phy Device Capabilities SAS Address TypeSdmcli show phy Calhoun Show phy aliasZoning Active Zone Group Number Zoning Inactive * phy may be assigned to a zone groupSDM-CLI Version SDM-D Version Sdmcli show phy Lincoln01Sdmcli show version Show phy alias phyShow zoneset data name Sdmcli show zoneset data ZoneOne Sdmcli show zonegroup ZoneOne#001Sdmcli show zoneset active Show zonegroup nameXip -i get avail Xip -i 500062b15555557f get expTroubleshooting