LSI SAS6160 Guide you through the configuration process, Check box and clicking the Delete button

Page 43

LSISAS6160 SAS Switch User Guide

Chapter 3: SAS Domain Manager Graphical User Interface Domain Tab

3.6.2.3 End Device Wizard

Use the End Device Wizard to automatically configure a zone set and associated zone

 

groups by grouping end devices. Each window of the wizard includes instructions to

 

guide you through the configuration process.

 

This wizard uses a snapshot of the current domain to determine the available end

 

devices and then displays lists of initiators and targets. Type the zone set name

 

(maximum of 28 characters) and bundle one or more initiators with one or more targets

 

into a zone by selecting them from these lists. You can define multiple zones as needed

 

in order to meet your zoning requirements. Zones can overlap, but zones that are

 

subsets of larger zones are removed. The wizard forces devices that share the same

 

ZPSDS entry point (siblings) into the same zone by automatically selecting all siblings

 

when you select a single sibling. You can delete the defined zones by selecting the

 

check box and clicking the Delete button.

 

After you define all the zones, the wizard uses the zone definitions to create the

 

minimal number of zone groups and to configure their permissions. The wizard creates

 

one zone group per defined zone, populating the zone group with the ZPSDS entry

 

point phys of the end devices in that zone, and setting up permission for the phys in

 

the zone group to communicate with each other.

 

The wizard then compares each zone group to all other zone groups, including zone

 

groups created during this process, searching for phys that are in both zone groups. If it

 

finds any such phys (parents), it creates a new zone group (child) and moves the

 

identified phys to the child. The wizard then grants permission for the child’s phys to

 

communicate with each other, as well as with the phys of the two parent zone groups.

 

If one of the parent zone groups is emptied in this process, the wizard transfers all

 

permissions from the parent to the child. Empty zone groups are later ignored and are

 

not transferred to the zone manager.

 

The wizard creates the zone set and associated zone group when you click the Apply

 

button. The wizard assigns to zone groups the names <zone set name> + #001, <zone

 

set name> + #002, and so on. If the number of generated zone groups exceeds the

 

maximum number of 248, the wizard displays an error message.

LSI Corporation September 2010

Page 43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Chapter FeaturesLSISAS6160 Switch Serial Attached Scsi and the SAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch Link between Two Single SAS Phys SAS Phys, Ports, and ConnectorsNarrow and Wide SAS Ports Mini SAS 4x Cable SAS Connectors and CablingSAS Zoning Overview Minimize conflictsOnly the storage within its zone or zones Across the entire ZpsdsFollowing figure shows a simple example of zoning Groups and zone sets manually by using the SDM utilityCreating SAS Zones Overview SAS Routing and Zoning Configuration for Zoning Example Creating Zone Groups Connecting Devices to the SAS6160 SwitchExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Carton contains the following items Unpacking the SwitchIdentifying Switch Components To interpret the LEDs on the switchSAS6160 LEDs Installing the SAS6160 SwitchSAS6160 Connectors CablesRack. These options are shown in the following figure Mounting Shelf in a Rack Setting a Static IP Address Connecting to a Host Changing the Default Static IP AddressFor example Exit SDM-GUI and power cycle the switchExit SDM-CLI and power cycle the switch Using SDM-GUI1 FCC Connecting SAS and Sata Hardware Safety NoticesCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices Starting SDM-GUI SDM-GUI AccountsEmbedded SDM only supports a single domain OptionsFile, Server, and Help Menu Options View End Device Table Information is available to both admin and user accountsViews Tab For zoningAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsAlias Management Domain TabThis section, click the hyperlinks on the Domain tab Node100, and so onDomain. You also can also this command to delete aliases View/Delete Aliases commandView/Delete Aliases Group to communicate with each other Connector WizardZone set and the two associated zone groups Box and clicking the Delete buttonZone group to communicate with each other Guide you through the configuration processMaximum number of 248, the wizard displays an error message Check box and clicking the Delete buttonCreate Zone Group Manually Configure Zone Groups Create Zone GroupDelete Zone Group Time of activation. shows the View Zone Group windowView Zone Group Modify Zone GroupMatrix Maximum password length is 32 charactersBinary 0, as defined by the SAS 2.0 specification PasswordModify Zone Set View Zone Set windowZone set View Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetDelete Zone Set Window and then clicking DeleteDevice Tree and Properties Tab Devices TabFollowing figure shows the Properties tab Selected device. In , the domain properties are shownProperties Tab Environmentals Tab Background loopFollowing figure shows the Attached Devices tab Those connectionsAttached Devices Tab Following figure shows the Phys tab Selected expanderZone Group Tab Zone Group TabOperations Tab This tab contains the following commandsSuccessful update Update FirmwarePhys Following figure shows the Enable/Disable/Reset windowEnable/Disable/Reset Reset SwitchAs shown in the following figures Configure IPCommand arguments Command Usage SyntaxDomain focus domain name SDM-CLI CommandsHelp command „ help commandExit Passwd admin user„ passwd admin „ passwd user„ alias delete „ show zoneset „ show alias„ show phy „ show zonegroup„ zonegroup delete all noconfirm „ zonegroup add name sas addressaliasphy„ zonegroup create name „ zonegroup delete single name„ zoneset create name Set membership„ zoneset activate name „ zoneset add name zone group zone groupSdmcli show alias Calhoun Sample Output for Show Command„ zoneset passwd Sdmcli show aliasSdmcli show device Calhoun Show phy Sdmcli show domainSdmcli show phy Show domainShow phy alias Alias Phy Device Capabilities SAS Address TypeSdmcli show phy Calhoun RA Routing Attributes VP Virtual PHY Zone GrpZoning Inactive * phy may be assigned to a zone group Zoning Active Zone Group NumberShow phy alias phy Sdmcli show phy Lincoln01Sdmcli show version SDM-CLI Version SDM-D VersionShow zonegroup name Sdmcli show zonegroup ZoneOne#001Sdmcli show zoneset active Show zoneset data name Sdmcli show zoneset data ZoneOneXip -i 500062b15555557f get exp Xip -i get availTroubleshooting
Top Page Image Contents