LSI SAS6160 View/Delete Aliases command, Domain. You also can also this command to delete aliases

Page 41

LSISAS6160 SAS Switch User Guide

Chapter 3: SAS Domain Manager Graphical User Interface Domain Tab

	Alias names must be unique and must not resemble valid SAS addresses (16
	hexadecimal characters that start with the number 5). The only special characters you
	can use in an alias are pound (#), dash, and underscore. The tree displays aliases only for
	the devices presently in the domain. To see aliases for other devices, use the
	View/Delete Aliases command.
3.6.1.2 View/Delete Aliases	Use the View/Delete Aliases command to display a list of all aliases associated with the
	focused domain, including aliases assigned to devices that are not presently in the
	domain. You also can also this command to delete aliases.

3.6.2Automatically Configure Zone Groups and Zone Sets

3.6.2.1Initiator Isolation Wizard

Figure 7: View/Delete Aliases

To delete an alias, select the check box next to it and click Delete.

Zoning wizards simplify zone set creation. The Automatically Configure Zone Groups and Zone Sets commands include three wizards that can automate the configuration of zone groups and zone sets.

The Initiator Isolation Wizard creates a zone set that isolates initiators from one another, while exposing all targets to each other. Use the Initiator Isolation Wizard to automatically configure a zone set and two associated zone groups based on a snapshot of the current domain. Each window of the wizard includes instructions to guide you through the configuration process.

After it prompts you to type the zone set name (maximum of 28 characters), the wizard checks the domain to determine if any initiators or targets are attached to the ZPSDS at the same point and share a common ZPSDS entry point. If so, the topology cannot support this zoning configuration, and the wizard terminates with an error message.

LSI Corporation September 2010

Page 41

Image 41

Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Chapter FeaturesLSISAS6160 Switch Serial Attached Scsi and the SAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch Link between Two Single SAS Phys SAS Phys, Ports, and ConnectorsNarrow and Wide SAS Ports Mini SAS 4x Cable SAS Connectors and CablingOnly the storage within its zone or zones Minimize conflictsAcross the entire Zpsds SAS Zoning OverviewCreating SAS Zones Groups and zone sets manually by using the SDM utilityFollowing figure shows a simple example of zoning Overview SAS Routing and Zoning Configuration for Zoning Example Creating Zone Groups Connecting Devices to the SAS6160 SwitchExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Identifying Switch Components Unpacking the SwitchTo interpret the LEDs on the switch Carton contains the following itemsSAS6160 Connectors Installing the SAS6160 SwitchCables SAS6160 LEDsRack. These options are shown in the following figure Mounting Shelf in a Rack Setting a Static IP Address Connecting to a Host Changing the Default Static IP AddressExit SDM-CLI and power cycle the switch Exit SDM-GUI and power cycle the switchUsing SDM-GUI For example1 FCC Connecting SAS and Sata Hardware Safety NoticesCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices Starting SDM-GUI SDM-GUI AccountsEmbedded SDM only supports a single domain OptionsFile, Server, and Help Menu Options Views Tab Information is available to both admin and user accountsFor zoning View End Device TableAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsThis section, click the hyperlinks on the Domain tab Domain TabNode100, and so on Alias ManagementView/Delete Aliases View/Delete Aliases commandDomain. You also can also this command to delete aliases Zone set and the two associated zone groups Connector WizardBox and clicking the Delete button Group to communicate with each otherMaximum number of 248, the wizard displays an error message Guide you through the configuration processCheck box and clicking the Delete button Zone group to communicate with each otherCreate Zone Group Manually Configure Zone Groups Create Zone GroupView Zone Group Time of activation. shows the View Zone Group windowModify Zone Group Delete Zone GroupBinary 0, as defined by the SAS 2.0 specification Maximum password length is 32 charactersPassword MatrixZone set View Zone Set windowView Zone Set Modify Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetDelete Zone Set Window and then clicking DeleteDevice Tree and Properties Tab Devices TabProperties Tab Selected device. In , the domain properties are shownFollowing figure shows the Properties tab Environmentals Tab Background loopAttached Devices Tab Those connectionsFollowing figure shows the Attached Devices tab Following figure shows the Phys tab Selected expanderZone Group Tab Zone Group TabSuccessful update This tab contains the following commandsUpdate Firmware Operations TabEnable/Disable/Reset Following figure shows the Enable/Disable/Reset windowReset Switch PhysAs shown in the following figures Configure IPCommand arguments Command Usage SyntaxHelp command SDM-CLI Commands„ help command Domain focus domain name„ passwd admin Passwd admin user„ passwd user Exit„ alias delete „ show phy „ show alias„ show zonegroup „ show zoneset„ zonegroup create name „ zonegroup add name sas addressaliasphy„ zonegroup delete single name „ zonegroup delete all noconfirm„ zoneset activate name Set membership„ zoneset add name zone group zone group „ zoneset create name„ zoneset passwd Sample Output for Show CommandSdmcli show alias Sdmcli show alias CalhounSdmcli show device Calhoun Sdmcli show phy Sdmcli show domainShow domain Show phySdmcli show phy Calhoun Alias Phy Device Capabilities SAS Address TypeRA Routing Attributes VP Virtual PHY Zone Grp Show phy aliasZoning Inactive * phy may be assigned to a zone group Zoning Active Zone Group NumberSdmcli show version Sdmcli show phy Lincoln01SDM-CLI Version SDM-D Version Show phy alias phySdmcli show zoneset active Sdmcli show zonegroup ZoneOne#001Show zoneset data name Sdmcli show zoneset data ZoneOne Show zonegroup nameXip -i 500062b15555557f get exp Xip -i get availTroubleshooting