LSI SAS6160 Set membership, zoneset activate name, zoneset add name zone group zone group

Page 65

LSISAS6160 SAS Switch User Guide

Chapter 4: SAS Domain Manager Command Line Interface SDM-CLI Commands

4.2.9	Zoneset Command	(Intra-Domain) Use the zoneset command to manage zone sets and zone
		set membership.

NOTE: Only the zoneset activate and zoneset deactivate commands affect the state of the active zone set. Other zone group commands and zone set commands have no effect until you subsequently activate the zone set.

Authority: Admin

Syntax:

zoneset activate <name>

zoneset add <name> <zone group> <zone group> zoneset create <name>

zoneset deactivate

zoneset delete (single <name> all [noconfirm]) zoneset passwd

zoneset remove <name> <zone group> <zone group> zoneset rename <old> <new>

Usage:

zoneset activate <name>

Activates a zone set after prompting you for the zone manager password. Only a single zone set can be active at a time, so this command also deactivates the current active zone set before it activates a new one. Changes to the active zone set, or changes to zone group permissions, do not take effect until the next zone set activates.

NOTE: Depending on the zoning configuration and how SDM accesses a domain, you might not always be required to enter a valid Zone Manager Password to modify or disable zoning after it is enabled. You can apply changes made to the active zone set by reactivating it. SDM-D validates the zone set within the current topology when activation occurs.

zoneset add <name> <zone group> <zone group>

Adds two zone groups to an existing zone set, which gives them permission to communicate with one another. The maximum number of zone groups is 248 for a zone set.

NOTE: A phy can only be a member of one zone group per zone set.

zoneset create <name>

Creates a new zone set. The zone set name can have a maximum of 32 characters. Valid characters are 0 through 9, A through Z, a through z, # (pound), - (dash), and _ (underscore).

zoneset deactivate

Deactivates the active zone set after it prompts you for the zone manager password.

LSI Corporation September 2010

Page 65

Image 65

Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Chapter FeaturesLSISAS6160 Switch Serial Attached Scsi and the SAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch Link between Two Single SAS Phys SAS Phys, Ports, and ConnectorsNarrow and Wide SAS Ports Mini SAS 4x Cable SAS Connectors and CablingOnly the storage within its zone or zones Minimize conflictsAcross the entire Zpsds SAS Zoning OverviewCreating SAS Zones Groups and zone sets manually by using the SDM utilityFollowing figure shows a simple example of zoning Overview SAS Routing and Zoning Configuration for Zoning Example Creating Zone Groups Connecting Devices to the SAS6160 SwitchExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Identifying Switch Components Unpacking the SwitchTo interpret the LEDs on the switch Carton contains the following itemsSAS6160 Connectors Installing the SAS6160 SwitchCables SAS6160 LEDsRack. These options are shown in the following figure Mounting Shelf in a Rack Setting a Static IP Address Connecting to a Host Changing the Default Static IP AddressExit SDM-CLI and power cycle the switch Exit SDM-GUI and power cycle the switchUsing SDM-GUI For example1 FCC Connecting SAS and Sata Hardware Safety NoticesCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices Starting SDM-GUI SDM-GUI AccountsEmbedded SDM only supports a single domain OptionsFile, Server, and Help Menu Options Views Tab Information is available to both admin and user accountsFor zoning View End Device TableAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsThis section, click the hyperlinks on the Domain tab Domain TabNode100, and so on Alias ManagementView/Delete Aliases View/Delete Aliases commandDomain. You also can also this command to delete aliases Zone set and the two associated zone groups Connector WizardBox and clicking the Delete button Group to communicate with each otherMaximum number of 248, the wizard displays an error message Guide you through the configuration processCheck box and clicking the Delete button Zone group to communicate with each otherCreate Zone Group Manually Configure Zone Groups Create Zone GroupView Zone Group Time of activation. shows the View Zone Group windowModify Zone Group Delete Zone GroupBinary 0, as defined by the SAS 2.0 specification Maximum password length is 32 charactersPassword MatrixZone set View Zone Set windowView Zone Set Modify Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetDelete Zone Set Window and then clicking DeleteDevice Tree and Properties Tab Devices TabProperties Tab Selected device. In , the domain properties are shownFollowing figure shows the Properties tab Environmentals Tab Background loopAttached Devices Tab Those connectionsFollowing figure shows the Attached Devices tab Following figure shows the Phys tab Selected expanderZone Group Tab Zone Group TabSuccessful update This tab contains the following commandsUpdate Firmware Operations TabEnable/Disable/Reset Following figure shows the Enable/Disable/Reset windowReset Switch PhysAs shown in the following figures Configure IPCommand arguments Command Usage SyntaxHelp command SDM-CLI Commands„ help command Domain focus domain name„ passwd admin Passwd admin user„ passwd user Exit„ alias delete „ show phy „ show alias„ show zonegroup „ show zoneset„ zonegroup create name „ zonegroup add name sas addressaliasphy„ zonegroup delete single name „ zonegroup delete all noconfirm„ zoneset activate name Set membership„ zoneset add name zone group zone group „ zoneset create name„ zoneset passwd Sample Output for Show CommandSdmcli show alias Sdmcli show alias CalhounSdmcli show device Calhoun Sdmcli show phy Sdmcli show domainShow domain Show phySdmcli show phy Calhoun Alias Phy Device Capabilities SAS Address TypeRA Routing Attributes VP Virtual PHY Zone Grp Show phy aliasZoning Inactive * phy may be assigned to a zone group Zoning Active Zone Group NumberSdmcli show version Sdmcli show phy Lincoln01SDM-CLI Version SDM-D Version Show phy alias phySdmcli show zoneset active Sdmcli show zonegroup ZoneOne#001Show zoneset data name Sdmcli show zoneset data ZoneOne Show zonegroup nameXip -i 500062b15555557f get exp Xip -i get availTroubleshooting