LSI SAS6160 manual Sdmcli show phy Lincoln01, Sdmcli show version, SDM-CLI Version SDM-D Version

Page 71

LSISAS6160 SAS Switch User Guide	Chapter 4: SAS Domain Manager Command Line Interface Sample Output for Show Com-
	mand

030	T	-	Enabled	6.0	*	5000c500176a32cd	000	End	000000010
031	T	-	Enabled	6.0	*	5000c500176c9211	000	End	000000010
032	T	-	Enabled	6.0	-	Poydras	016	Switch	000001000
033	T	-	Enabled	6.0	-	Poydras	017	Switch	000001000
034	T	-	Enabled	6.0	-	Poydras	018	Switch	000001000
035	T	-	Enabled	6.0	-	Poydras	019	Switch	000001000
036	D	*	Enabled	6.0	-	50012be0000380fd	000	End	010100010
037	D	*	Enabled	-	-	----------------	---	None	000000100

4.3.8	show phy <alias>: <phy>	SDMCLI> show phy Lincoln:01
		===============================================
		Phy Information
		===============================================
		SAS Address: 500605b0000282bf
		Phy Identifier:	01
		State:	Enabled
		Link Speed:	6.0 Gb/s
		Virtual Phy:	No
		Routing Attribute:	Subtractive
		Minimum Link Speed:	1.5 Gb/s
		Maximum Link Speed:	6.0 Gb/s
		Supported Minimum Link Speed:	1.5 Gb/s
		Supported Maximum Link Speed:	6.0 Gb/s
		Connector Type:	No Information
		Connector Element Index:	00
		Connector Physical Link:	00
		Phy Fault LED:	OFF
		Phy Change Count:	2
		SAS Zone Group:	Zoning Inactive
		- Attached Device Information	-
		Attached SAS Address:	500605b0006b75c0
		Attached Phy Identifier:	06
		Attached Device Type: End Device
		Attached Device Capabilities: SAS Management Initiator
			SATA Initiator (SAS Tunneled)
			SAS Initiator
		- Error Statistics -	Count: 0
		Invalid Dword	Count: 0
		Running Disparity Error	Count: 0
		Loss of Dword Synchronization	Count: 0
		Phy Reset Problem	Count: 0
4.3.9	show version	SDMCLI> show version
		SDM-CLI Version 2.250.5.0
		SDM-D Version 2.250.5.0

LSI Corporation September 2010

Page 71

Image 71

Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Chapter FeaturesLSISAS6160 Switch Serial Attached Scsi and the SAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch Link between Two Single SAS Phys SAS Phys, Ports, and ConnectorsNarrow and Wide SAS Ports Mini SAS 4x Cable SAS Connectors and CablingSAS Zoning Overview Minimize conflictsOnly the storage within its zone or zones Across the entire ZpsdsCreating SAS Zones Groups and zone sets manually by using the SDM utilityFollowing figure shows a simple example of zoning Overview SAS Routing and Zoning Configuration for Zoning Example Creating Zone Groups Connecting Devices to the SAS6160 SwitchExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Carton contains the following items Unpacking the SwitchIdentifying Switch Components To interpret the LEDs on the switchSAS6160 LEDs Installing the SAS6160 SwitchSAS6160 Connectors CablesRack. These options are shown in the following figure Mounting Shelf in a Rack Setting a Static IP Address Connecting to a Host Changing the Default Static IP AddressFor example Exit SDM-GUI and power cycle the switchExit SDM-CLI and power cycle the switch Using SDM-GUI1 FCC Connecting SAS and Sata Hardware Safety NoticesCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices Starting SDM-GUI SDM-GUI AccountsEmbedded SDM only supports a single domain OptionsFile, Server, and Help Menu Options View End Device Table Information is available to both admin and user accountsViews Tab For zoningAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsAlias Management Domain TabThis section, click the hyperlinks on the Domain tab Node100, and so onView/Delete Aliases View/Delete Aliases commandDomain. You also can also this command to delete aliases Group to communicate with each other Connector WizardZone set and the two associated zone groups Box and clicking the Delete buttonZone group to communicate with each other Guide you through the configuration processMaximum number of 248, the wizard displays an error message Check box and clicking the Delete buttonCreate Zone Group Manually Configure Zone Groups Create Zone GroupDelete Zone Group Time of activation. shows the View Zone Group windowView Zone Group Modify Zone GroupMatrix Maximum password length is 32 charactersBinary 0, as defined by the SAS 2.0 specification PasswordModify Zone Set View Zone Set windowZone set View Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetDelete Zone Set Window and then clicking DeleteDevice Tree and Properties Tab Devices TabProperties Tab Selected device. In , the domain properties are shownFollowing figure shows the Properties tab Environmentals Tab Background loopAttached Devices Tab Those connectionsFollowing figure shows the Attached Devices tab Following figure shows the Phys tab Selected expanderZone Group Tab Zone Group TabOperations Tab This tab contains the following commandsSuccessful update Update FirmwarePhys Following figure shows the Enable/Disable/Reset windowEnable/Disable/Reset Reset SwitchAs shown in the following figures Configure IPCommand arguments Command Usage SyntaxDomain focus domain name SDM-CLI CommandsHelp command „ help commandExit Passwd admin user„ passwd admin „ passwd user„ alias delete „ show zoneset „ show alias„ show phy „ show zonegroup„ zonegroup delete all noconfirm „ zonegroup add name sas addressaliasphy„ zonegroup create name „ zonegroup delete single name„ zoneset create name Set membership„ zoneset activate name „ zoneset add name zone group zone groupSdmcli show alias Calhoun Sample Output for Show Command„ zoneset passwd Sdmcli show aliasSdmcli show device Calhoun Show phy Sdmcli show domainSdmcli show phy Show domainShow phy alias Alias Phy Device Capabilities SAS Address TypeSdmcli show phy Calhoun RA Routing Attributes VP Virtual PHY Zone GrpZoning Inactive * phy may be assigned to a zone group Zoning Active Zone Group NumberShow phy alias phy Sdmcli show phy Lincoln01Sdmcli show version SDM-CLI Version SDM-D VersionShow zonegroup name Sdmcli show zonegroup ZoneOne#001Sdmcli show zoneset active Show zoneset data name Sdmcli show zoneset data ZoneOneXip -i 500062b15555557f get exp Xip -i get availTroubleshooting