LSI SAS6160 manual Sample Output for Show Command, zoneset passwd, Sdmcli show alias

Page 66

Chapter 4: SAS Domain Manager Command Line Interface Sample Output for Show Com-	LSISAS6160 SAS Switch User Guide
mand

4.3Sample Output for Show Command

4.3.1show alias

4.3.2show alias <alias>

4.3.3show device

NOTE: Zoning within the domain is disabled when no zone set is active, and access is unrestricted. Therefore, all end devices in the domain can see one another.

zoneset delete single <name>

Deletes a single zone set.

zoneset delete all [noconfirm]

Deletes all zone sets. If you specify the [noconfirm] option, the action occurs immediately without an additional confirmation prompt. Otherwise, SDM first prompts you to confirm the action.

zoneset passwd

Starts a dialog to change and synchronize the password on all zoning expanders throughout the domain. Passwords are text strings that contains any valid ASCII character. The maximum password length is 32 characters.

NOTE: The default zone manager password is lynx.

zoneset remove <name> <zone group> <zone group>

Removes communication privileges between two zone groups in an existing zone set. A zone group is purged from the zone set if no other communication privileges remain.

zoneset rename <old> <new>

Renames an existing zone set.

This section shows sample output for some variations of the show command. The first line of each example shows the actual syntax of the command that you enter at the SDMCLI> prompt.

The examples in this section detail the show command output.

SDMCLI> show alias
SAS Address	Alias

-----------------------------------------------------

500605b0006b75b0	Bacchus
50012be0000380ff	Calhoun
500605b0000220bf	Carrollton
SDMCLI> show alias Calhoun
SAS Address	Alias

------------------------------------------

50012be0000380ff Calhoun

SDMCLI> show device

NOTE: In the following example, ZExpander means zoning capable expander.

Page 66

LSI Corporation September 2010

Image 66

Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Features ChapterSerial Attached Scsi and the SAS6160 Switch LSISAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch SAS Phys, Ports, and Connectors Link between Two Single SAS PhysNarrow and Wide SAS Ports SAS Connectors and Cabling Mini SAS 4x CableAcross the entire Zpsds Minimize conflictsOnly the storage within its zone or zones SAS Zoning OverviewGroups and zone sets manually by using the SDM utility Following figure shows a simple example of zoningCreating SAS Zones Overview SAS Routing and Zoning Configuration for Zoning Example Connecting Devices to the SAS6160 Switch Creating Zone GroupsExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration To interpret the LEDs on the switch Unpacking the SwitchIdentifying Switch Components Carton contains the following itemsCables Installing the SAS6160 SwitchSAS6160 Connectors SAS6160 LEDsRack. These options are shown in the following figure Mounting Shelf in a Rack Connecting to a Host Changing the Default Static IP Address Setting a Static IP AddressUsing SDM-GUI Exit SDM-GUI and power cycle the switchExit SDM-CLI and power cycle the switch For exampleConnecting SAS and Sata Hardware Safety Notices 1 FCCCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices SDM-GUI Accounts Starting SDM-GUIOptions Embedded SDM only supports a single domainFile, Server, and Help Menu Options For zoning Information is available to both admin and user accountsViews Tab View End Device TableAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsNode100, and so on Domain TabThis section, click the hyperlinks on the Domain tab Alias ManagementView/Delete Aliases command Domain. You also can also this command to delete aliasesView/Delete Aliases Box and clicking the Delete button Connector WizardZone set and the two associated zone groups Group to communicate with each otherCheck box and clicking the Delete button Guide you through the configuration processMaximum number of 248, the wizard displays an error message Zone group to communicate with each otherManually Configure Zone Groups Create Zone Group Create Zone GroupModify Zone Group Time of activation. shows the View Zone Group windowView Zone Group Delete Zone GroupPassword Maximum password length is 32 charactersBinary 0, as defined by the SAS 2.0 specification MatrixView Zone Set View Zone Set windowZone set Modify Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetWindow and then clicking Delete Delete Zone SetDevices Tab Device Tree and Properties TabSelected device. In , the domain properties are shown Following figure shows the Properties tabProperties Tab Background loop Environmentals TabThose connections Following figure shows the Attached Devices tabAttached Devices Tab Selected expander Following figure shows the Phys tabZone Group Tab Zone Group TabUpdate Firmware This tab contains the following commandsSuccessful update Operations TabReset Switch Following figure shows the Enable/Disable/Reset windowEnable/Disable/Reset PhysConfigure IP As shown in the following figuresCommand Usage Syntax Command arguments„ help command SDM-CLI CommandsHelp command Domain focus domain name„ passwd user Passwd admin user„ passwd admin Exit„ alias delete „ show zonegroup „ show alias„ show phy „ show zoneset„ zonegroup delete single name „ zonegroup add name sas addressaliasphy„ zonegroup create name „ zonegroup delete all noconfirm„ zoneset add name zone group zone group Set membership„ zoneset activate name „ zoneset create nameSdmcli show alias Sample Output for Show Command„ zoneset passwd Sdmcli show alias CalhounSdmcli show device Calhoun Show domain Sdmcli show domainSdmcli show phy Show phyRA Routing Attributes VP Virtual PHY Zone Grp Alias Phy Device Capabilities SAS Address TypeSdmcli show phy Calhoun Show phy aliasZoning Active Zone Group Number Zoning Inactive * phy may be assigned to a zone groupSDM-CLI Version SDM-D Version Sdmcli show phy Lincoln01Sdmcli show version Show phy alias phyShow zoneset data name Sdmcli show zoneset data ZoneOne Sdmcli show zonegroup ZoneOne#001Sdmcli show zoneset active Show zonegroup nameXip -i get avail Xip -i 500062b15555557f get expTroubleshooting