LSI SAS6160 manual Passwd admin user, passwd admin, passwd user, Exit, Logout quit

Page 61

LSISAS6160 SAS Switch User Guide

4.2.3Passwd Command

4.2.4Quit Command

4.2.5Alias Command

Chapter 4: SAS Domain Manager Command Line Interface SDM-CLI Commands

(Extra-Domain) Use the passwd command to change the password for an account after prompting for the admin password. Passwords must have between four and 16 characters.

Authority: Admin

Syntax:

passwd (admin user)

Usage:

passwd admin

Starts a dialog to change the password for the admin account.

passwd user

Starts the following dialog to change the password for the user account:

SDMCLI> passwd user passwd user

Please enter the current 'admin' password: *****

Please enter the new password for user: *****

Please re-enter the new password for user: *****

Password changed.

(Extra-Domain) Use the quit command (or the exit or logout command) to log out and exit SDM-CLI.

Authority: User

Syntax:

exit

logout quit

(Intra-Domain) Use the alias command to create or delete aliases. An alias is a user-defined name that is bound to a SAS address. After you create an alias, you can use it anywhere that you would normally use a SAS address.

NOTE: You can assign only a single alias to a SAS address.

SDM does not use aliases directly. For example, if you use an alias to define a zone group, SDM does not track the alias in the zone group’s structures. Instead, it tracks the SAS address bound to the alias. Therefore, the zone group is not affected if you make subsequent changes to the alias.

Authority: Admin

Syntax:

alias create <name> <sas address>

alias delete (single <name> all [noconfirm])

LSI Corporation September 2010

Page 61

Image 61

Contents LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Chapter FeaturesLSISAS6160 Switch Serial Attached Scsi and the SAS6160 SwitchLSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch Link between Two Single SAS Phys SAS Phys, Ports, and ConnectorsNarrow and Wide SAS Ports Mini SAS 4x Cable SAS Connectors and CablingOnly the storage within its zone or zones Minimize conflictsAcross the entire Zpsds SAS Zoning OverviewFollowing figure shows a simple example of zoning Groups and zone sets manually by using the SDM utilityCreating SAS Zones Overview SAS Routing and Zoning Configuration for Zoning Example Creating Zone Groups Connecting Devices to the SAS6160 SwitchExample 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Identifying Switch Components Unpacking the SwitchTo interpret the LEDs on the switch Carton contains the following itemsSAS6160 Connectors Installing the SAS6160 SwitchCables SAS6160 LEDsRack. These options are shown in the following figure Mounting Shelf in a Rack Setting a Static IP Address Connecting to a Host Changing the Default Static IP AddressExit SDM-CLI and power cycle the switch Exit SDM-GUI and power cycle the switchUsing SDM-GUI For example1 FCC Connecting SAS and Sata Hardware Safety NoticesCanada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices Starting SDM-GUI SDM-GUI AccountsEmbedded SDM only supports a single domain OptionsFile, Server, and Help Menu Options Views Tab Information is available to both admin and user accountsFor zoning View End Device TableAlias Table View Zone Groups View Zone GroupsView Zone Sets View Zone SetsThis section, click the hyperlinks on the Domain tab Domain TabNode100, and so on Alias ManagementDomain. You also can also this command to delete aliases View/Delete Aliases commandView/Delete Aliases Zone set and the two associated zone groups Connector WizardBox and clicking the Delete button Group to communicate with each otherMaximum number of 248, the wizard displays an error message Guide you through the configuration processCheck box and clicking the Delete button Zone group to communicate with each otherCreate Zone Group Manually Configure Zone Groups Create Zone GroupView Zone Group Time of activation. shows the View Zone Group windowModify Zone Group Delete Zone GroupBinary 0, as defined by the SAS 2.0 specification Maximum password length is 32 charactersPassword MatrixZone set View Zone Set windowView Zone Set Modify Zone SetActivate/Deactivate Zone Set Activate/Deactivate Zone SetDelete Zone Set Window and then clicking DeleteDevice Tree and Properties Tab Devices TabFollowing figure shows the Properties tab Selected device. In , the domain properties are shownProperties Tab Environmentals Tab Background loopFollowing figure shows the Attached Devices tab Those connectionsAttached Devices Tab Following figure shows the Phys tab Selected expanderZone Group Tab Zone Group TabSuccessful update This tab contains the following commandsUpdate Firmware Operations TabEnable/Disable/Reset Following figure shows the Enable/Disable/Reset windowReset Switch PhysAs shown in the following figures Configure IPCommand arguments Command Usage SyntaxHelp command SDM-CLI Commands„ help command Domain focus domain name„ passwd admin Passwd admin user„ passwd user Exit„ alias delete „ show phy „ show alias„ show zonegroup „ show zoneset„ zonegroup create name „ zonegroup add name sas addressaliasphy„ zonegroup delete single name „ zonegroup delete all noconfirm„ zoneset activate name Set membership„ zoneset add name zone group zone group „ zoneset create name„ zoneset passwd Sample Output for Show CommandSdmcli show alias Sdmcli show alias CalhounSdmcli show device Calhoun Sdmcli show phy Sdmcli show domainShow domain Show phySdmcli show phy Calhoun Alias Phy Device Capabilities SAS Address TypeRA Routing Attributes VP Virtual PHY Zone Grp Show phy aliasZoning Inactive * phy may be assigned to a zone group Zoning Active Zone Group NumberSdmcli show version Sdmcli show phy Lincoln01SDM-CLI Version SDM-D Version Show phy alias phySdmcli show zoneset active Sdmcli show zonegroup ZoneOne#001Show zoneset data name Sdmcli show zoneset data ZoneOne Show zonegroup nameXip -i 500062b15555557f get exp Xip -i get availTroubleshooting