Lantronix 2100 Australia/New Zealand, Disclaimer and Supplementary Information, BCompliance UBox

Page 72

B:Compliance – UBox 4100

Translation:

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Australia/New Zealand

This device complies with AS/NZS 3548 Class B limits for the operation of Information Technology Equipment.

Disclaimer and Supplementary Information

The Lantronix UBox USB Server, Model UBox 4100, complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications to the UBox USB Device Server not expressly approved by Lantronix could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult Lantronix or an experienced radio/TV technician for help.

UBox User Guide

72

Image 72

Contents UBox USB Device Server User Guide Part Number Revision D JuneTrademark Copyright ContactsRevisions Lantronix Corporate HeadquartersContents Changing the UBoxs Settings ContentsResetting the UBox Hardware Troubleshooting USB DevicesTechnical Support CE Mark Declaration of ConformityDisconnect Printer for Auto Connect Using This Guide Purpose and AudienceSummary of Chapters Remaining chapters in this guide includeIntroduction Model and Part NumbersUSB Speeds and Throughput Supported Devices Compatible USB DevicesConnectivity to USB Devices Connectivity to a NetworkHub Support RequirementsWhats Inside the Package Windows Windows XP and Vista 32 bitInstalling the UBox Installing the UBox HardwareConnect the UBox’s Power Supply and Read the LEDs Connect the UBox to Your NetworkInstalling the UBox UDS4100 System LEDsInstalling the UBox Software To install the UBox SoftwareUSB Devices Tab Uninstalling the Lantronix UBox Software Servers Tab Displaying a UBoxUsing USB Devices on the Network Connecting Your USB DeviceOverview Connect a USB Device to the UBoxUsing USB Devices on the Network Review the following information on the USB Devices tabAction Connect a Networked USB Device Device NameStatus LocationDisconnect Your USB Devices Using Multiple UBoxes and USB Devices Compound DevicesOne UBox with Multiple Users Multiple UBoxes and USB DevicesOther Ways to Connect and Disconnect USB Devices UBox Groups on Multiple UDP PortsPC Connectivity to UBoxes and UBS Devices SummaryUsing the UBox System Tray Auto Connecting Printers To use the auto connect featureAuto Connect Enabled Disconnect Printer for Auto ConnectUsing Forced Device Disconnect To use Forced Device DisconnectOn the USB Devices tab, select the UBox to disconnect From the Advanced menu, select Force Device DisconnectUsing Multi-and Single-User Connect Modes Forced Device Disconnect on the Advanced MenuDevice Status Separating Compound Devices Types of USB DevicesSeparating Compound Devices To separate compound devicesChanging the UBoxs Settings Viewing UBox SettingsChanging the UBoxs Settings Status column, the following may displayServer # Server NameEditing Server Settings Access Tab To edit the UBox’s Settings on the Access TabFirmware Upgrade Update the following settings as desiredConnect Mode Editing Server Settings Network Tab IP Address AssignmentIP Address, Subnet Mask, and Gateway for the UBox Subnet Mask GatewayUDP Port TCP PortEditing Server Settings USB Device Configuration Tab Location/Serial NumberCfg Following information displays at the top Applying, Canceling, or Removing Server Settings Reenter Password Share ModeConnection Restoring Default Settings To restore the UBox to factory settingsTo update the firmware Updating the UBoxs FirmwareUpdate Server Firmware Click the Close button UBox User GuideOverriding Server Network Settings To override network settingsEnter the following information Refreshing Data You can get more information about ZeroConf atChanging Local Software Settings Updating Personal Communication SettingsTo update your computer’s settings Changing Local Software Settings Client NameMulticast Address Updating Server Access Settings Update the following information as neededViewing or Removing Device Passwords To view or remove USB device passwordsDevice Serial # Switching Between Sets of UBoxes Troubleshooting Troubleshooting Status LightsBefore You Begin ‹ OffTroubleshooting Status Lights on UBoxBoot-Up System Status LightSystem Status Lights 2 System 2 is On / SystemOff / System Status 2 is OffTroubleshooting UDP Ports Troubleshooting Network Issues Communication Between your PC and the UBoxTo ping the UBox Is Not ListedResetting the UBox Hardware Power-Cycling or Using the Reset ButtonFirewalls Final StepRebooting the UBox into Safe Mode Using the Reset Button To boot into safe modeTroubleshooting USB Devices To troubleshoot problems with USB DevicesTo troubleshoot issues with multiple users of a USB device Technical SupportTroubleshooting Status Light Behavior Position of Status Lights on the UBoxStatus Light Behavior If System 1 greenSystem 2 red/amber blink System 2 and System 3 both Refer to -4. UBox Status Lights -- UBox is RunningSystem 2= OFF and System 3= OFF System 2= on and System 3= OFFSystem 2= on and System 3= on System 2=OFF and System 3= onConfiguring the Windows XP Firewall To determine Windows XP versionAConfiguring the Windows XP Firewall To obtain your UDP and TCP port numbersTo obtain your IP address To obtain the Advanced Settings window Local Area Connection Properties Advanced TabAdvanced Settings Window To add your UDP Port to the firewallTo add your TCP port to the firewall To close the remaining windowsTo access your firewall software Select On Click the Exceptions tab UBox User Guide11. Exceptions Tab Select UDP Click OK 13. Add a Port Window TCPCompliance UBox CE Mark Declaration of ConformityCanada Digital Apparatus EMI Standard Manufacturers Name and AddressAustralia/New Zealand Disclaimer and Supplementary InformationBCompliance UBox TranslationRoHS Notice SLB SLP SCS SLS DSCDeclaration of Conformity CCompliance UBox Manufacturer’s Contact Lantronix Software License Agreement DLantronix Software License Agreement Lantronix Warranty

Related manuals

Manual 95 pages 52.43 Kb