Intelligent Motion Systems user manual UDAS-1001E Series Hardware Specifications

Page 40

Appendix A

Specifications

A.1 UDAS-1001E Series Hardware Specifications

All specifications are typical at 25ºC unless otherwise noted.

Note: When powered from an external source, the on-board power supply circuit can supply up to 200mA at 5V DC to termination panels through the 50-pin I/O connector.

PARAMETER	CONDITIONS	SPECIFICATION

Analog Inputs

Number of Channels	Single-ended	16

	Differential	8

Resolution		12-bits (1 part in 4096)

Voltage Ranges		0 - 10 V, ±10 V, ±5 V

Overvoltage Protection	Power on or off	±20 V

Software Programmable		1, 10, 100
Gains

Gain Accuracy	Gain = 1	0.02%

	Gain = 10	0.05%

	Gain = 100	0.08%

Input Offset Voltage		3mV

Input Bias Current		500 pA

Input Impedence		10+9 ohms/50 pF
Common Mode Input		±10 V
Range

Common Mode Rejection	60 Hz, 100 ohm imbalance

	Gain = 1	-85dB

	Gain >= 10	-90dB

	TABLE A.1 Hardware Specifications

A-1

Image 40

Contents UDAS-1001E Series Warranty and Repair Policy Statement GeneralTechnical Assistance and Service Static SensitivityOnline Support Email Support North American Customers International CustomersUse of Equipment TrademarksFCC Radio Frequency Interference Statement Revision History Table of Contents Specifications Introduction Features SoftwareSupport LibraryAnalog Input Analog OutputUdas 1001E Series Functional Description Data Acquisition FunctionsDigital Input/Output CounterStarting and Stopping the High-Speed Analog Input Mode High-Speed Analog Input ModeStarting Conversions Channel Scanner Rate GeneratorStopping Conversions High-Speed Analog Input Triggering Digital I/O Auto ZeroExample Counters UDAS-1001E-4 dimensional drawing Software Support and Accessories PowerDiagnostic Software SupportVisual Designer Udas Support Library LabVIEW Udas Support LibraryPower-on Default Digital I/O Configuration Removing the CoverSetting the Configuration Udas Switch S1Reinstalling the Cover Enabling the CJCDifferential JP1 Jumper Position JP2 Jumper Position Connecting the Udas Unit Making the Initial ConnectionChecking the System Installing and Running Udas Syscheck Installing SyscheckUse your CD drive letter\Syscheck\SETUP.EXEENTER Syscheck OperationUnit Info System Check Analog Input Test Analog Output Test Counter Test Udas Syscheck Counter Test Measure Input High Mode Udas Syscheck Counter Test Measure Frequency Mode Digital I/O Test Udas Syscheck Digital I/O TestPaced Analog Input 10 High-Speed Aquisition Sample Troubleshooting Tips USB PortTroubleshooting Errors Power TestUdas Drivers Check the wiring and cables for shorts or damage Specifications UDAS-1001E Series Hardware SpecificationsRMS USB UDAS-1001E-3, UDAS-1001E-4 Dimensions Figure A.1 Dimensions of the Udas unit Top viewFigure A.3 Dimensions of the Udas unit Bottom view Figure A.4 Dimensional Drawing of the Udas series PCB Udas I/O Connectors Udas I/O Connectors Udas I/O Connectors Accessories Udas Termination Panels PCI-20429T-1 Multifunction Termination PanelFigure B.2 PCI-20429T-1 Multifunction Termination Panel Udas Termination and Signal Conditioning Options A L O G T E R M I N a T I O N SFigure B.4 UDAS-1001E Termination Options Analog In Single-Ended and Differential Function Isolator Blocks Summary of FeaturesPCI-1100 Series Digital Opto-Isolator Blocks Removing the Udas Unit’s Cover Udas Analog Input Circuit Calibration ProceduresEquipment Required Analog Input and Output Calibration Procedures Adjust Offset and Gain for ±10Volt Input Range Analog Input Calibration ProcedureAdjust Input Offset Voltage Adjust Offset and Gain for ± 5Volt Input Range Adjust Offset and Gain for 0 to 10 Volt Range Udas Analog Output Circuit Calibration Procedure Analog Output Channel 0 Offset and Gain Analog Output Channel 1 Offset and GainIndex Udas Index-3