Intelligent Motion Systems manual N e r a l Specification s, MDI17 Acme Screws

Page 11

M D r i v e 1 7 M o t i o n C o n t r o l A C M E S c r e w

WARNING: The maximum axial load limit for the MDrive17 Linear motor is 50 lbs (22.7 kg). Do not exceed this rating!

WARNING: The ACME Screw MUST NOT deflect more than ± 1 degree perpendicular to the motor face. Additional support for radial loads may be required!

MDI17 ACME Screws

	Screw	Travel/Full Step - Inches (mm)
	A	0.00125	(0.3175)
	B	0.000625	(0.015875)
	C	0.0003125	(0.079375)
	D	0.00015625	(0.00396875)

Table 1.5: ACME Screws for the MDI17 Linear Actuator

G e n e r a l S p e c i f i c a t i o n s

I n p u t Vo l t a g e ( + V )
Range	+12 to +48 VDC
A n a l o g I n p u t
Resolution	10 Bit
Voltage Range	0 to +5 Volts
P r o g r a m m a b l e I / O
Number	4
Interface Type	Open Collector
Voltage Range	0 to +24 VDC
Output Sink Current	700 mA
Protection	Over Temp., Short Circuit, Inductive Clamp
C o m m u n i c a t i o n
Protocol	RS-485, Full/Half Duplex SelecTable 1.
BAUD Rate	4800, 9600, 19.2k, 38.0k, 115.2k
M o t i o n
Microstep Resolution (Open Loop Configuration)
Number of Settings	14
Steps per Revolution	400, 800, 1000, 1600, 2000, 3200, 5000
	6400, 10000, 12800, 25000, 25600, 50000
	51200
Microstep Resolution (Closed Loop Configuration)
Steps per Revolution (Fixed)	51200
Encoder (Optional)
Type	Internal, Magnetic
Resolution	512 Lines/2048 counts per Revolution
Counters
Type	Position(C1), Encoder (C2)
Resolution	32 Bit
Edge Rate (Max)	5 MHz
Velocity
Range	±5,000,000 Steps per Second
Resolution	1 Step per Second
Acceleration/Deceleration
Range	1.5 x 109 Steps per Second2
Resolution	90.9 Steps per Second2

9

Image 11

Contents Operating Instructions Intelligent Motion Systems, Inc All Rights Reserved Table of Contents List of Figures Part 1 General Information and Hardware Specifications Intentionally Left Blank A t u r e S u m m a r y Control Knob LMAX2 T a r y M o t o r Specification sC t i o n O v e r v i e w Standard Rotary Motor LmaxMDI1719 N e a r M o t o r Specification sMDI1715 E e d F o r c e C u r v e 4 5 V D C MDI17 Linear ActuatorE e d F o r c e C u r v e 2 4 V D C MDI17 Acme Screws N e r a l Specification sR i v e 1 7 M o t i o n C o n t r o l a C M E S c r e w C o m m e n d e d I M S P o w e r S u p p l i e s E r m a l Specification sW e r S u p p l y R e q u i r e m e n t s A t u r e S u m m a r y MDI2218 MDrive23 Motion Control SpecificationsMDI2231 MDI2222Refer to .10 for screw pitch information MDI23 Linear ActuatorMDI23 Acme Screws R i v e 2 3 M o t i o n C o n t r o l a C M E S c r e wIP404MDI23 Page Intentionally Left Blank C o m m e n d e d W i r i n g Connector P1Y o u t a n d I n t e r f a c e G u i d e l i n e s N C o n f i g u r a t i o n a n d D e s c r i p t i o n sN g l e M D r i v e Connector P2 10 Pin HeaderT e r f a c i n g P o w e r T e r f a c i n g R S 4 8 5 C o m m u n i c a t i o n sRS-485 Interface, Multiple MDrive Motion Control System Input Functions T e r f a c i n g t h e D i g i t a l I / OE s o f t h e D i g i t a l I / O T e r f a c i n g I n p u t sTruth Table I/O Used as a Group TTL Interface to Input GroupT e r f a c i n g a S i n g l e O u t p u t E x a m p l e s T e r f a c i n g O u t p u t sM p l e U s a g e T e r f a c i n g t h e a n a l o g I n p u tS t e m R e q u i r e m e n t s Install i n g a n d U s i n g I M S Te r m i n a lInstallation I n g t h e I M S Te r m i n a l S o f t w a r e 13 IMS Terminal Upgrader Window R i a b l e s R i v e M o t i o n C o n t r o l P r o g r a m m i n gE r a t i o n a l M o d e s S t r u c t i o n sY w o r d s A g sT i o n C o m m a n d s T h F u n c t i o n sC o m m a n d s Read IO1 Setup PR S1 Read IO2 Setup PR S2Please Note Any program labeled SU will execute on power-up VAR CT Baud Mnemonic Function Unit Range Syntax ExampleI n s t r u c t i o n s , Va r i a b l e s a n d F l a g s T h e m a t i c a l F u n c t i o n s Symbol FunctionRetrieve All Parameters Variable Baud Rate Setup VariableAcceleration Motion Variable Busy Flag Read Only Motion Flag Branch Program InstructionClear Program Program Instruction Set Counter 2 Encoder Counts Motion VariableCall Subroutine Program Instruction Deceleration Motion Variable Set Encoder Deadband Setup VariableD1-D5 Digital Input Filtering Variable End Program Execution Program Instruction Drive Enable Flag Setup FlagDevice Name Setup Variable Read-Only Error Flag Status Flag Encoder Enable Flag Setup FlagEcho Mode Flag Setup Flag Execute Program Program Instruction Error Number Variable Status VariableHold Program Execution Program Instruction Home to Index Mark Variable Setup VariableHold Current Setup Variable Read Input Variable Home to Home Switch Variable Setup VariableHold Current Delay Time Setup Variable Increment Variable Program Instruction Read Analog Input VariableRead Encoder Index Mark Variable Initialize Parameters Instruction Joystick Enable Flag Setup FlagRead Inputs 1-4 As 1 Value Variable Label Program/Subroutine Instruction Lock User Program Setup FlagList Program Space Instruction Move To Relative Position Motion Instruction Motion InstructionPR MS Microstep Resolution Motion VariableO1 O4 Set/Print Output Logic State Variable Motor Settling Delay Time Motion VariableOn Error Handler Instruction Set/Print Position Counter Instruction Set Ouputs 1-4 As 1 Value VariablePrint Selected Data/Text Instruction Postition Maintenance Enable Setup FlagEnter/Exit Program Mode Program Instruction Pause Program Instruction Party Mode Enable Flag Setup FlagR1 R4 User Registers User Variable Run Current Setup VariableSave to EEProm Instruction Resume Program InstructionReturn From Subroutine Instruction Set/Print I/O Point Instruction S1 S4 Set/Print I/O Point Type/Active State InstructionEncoder Variable Stall Detection Mode Variable Encoder VariableTrip on Input Variable Trip Enable Flag Setup FlagRead Only Stall Flag Encoder Flag Read User Variables Upgrade Firmware InstructionTrip on Position Variable Create User Variable Name Instruction Read Only Velocity Variable Motion VariableRead Only Firmware Version Factory Variable Appendix a Program Errors Error Code FaultErrors Data ErrorsTWENTY-FOUR Month Limited Warranty Western Region