GarrettCom 6K8 manual Www . GarrettCom . com

Page 31

Magnum 6K8-Series Industrial Field Switch

Installation and User Guide 03/06)

floor enclosure, maintained vertically for proper convection cooling of the unit. The Magnum 6K8 requires two DIN-Rail mounting clips or latches for secure mounting, and these may be ordered as Model # DIN-RAIL-6K8. See a 6K8 viewed from the rear, at right, with model DIN-RAIL-6K8 in place on the unit.

The Din Rail Latching clips are mounted on the upper rear corners of the 6K8 unit. Two threaded holes are provided on the sides of 6K8 for DIN- Rail mounting purposes. See side view at the left, with the top of the unit pointed to the right. The required two screws are included with the DIN- Rail brackets, and are no.10-32 X 3/8 PHIL. PAN w/star washer. The two heavy duty Din-Rail

latches are designed as if that they can be manually accessed from the top when the 6K8 is installed on a DIN Rail.

To install the 6K8 with the DIN-Rail brackets and latches attached to it, hold the 6K8 in the vertical position with the bottom out, and with the top moved in toward the DIN-Rail. Position the latches over the top of the DIN-Rail. Then, snap the latches into holding position by moving the bottom of the 6K8 inwards to a vertical position. The DIN-Rail latches and brackets are heavy duty, and will hold the 6K8 securely in position, even with cabling attached to the unit.

To release the 6K8 from the DIN-Rail mounting, press the top of the two DIN- Rail latches down simultaneously to release the 6K8 so that it can be dismounted by pulling the bottom out. Once the bottom of the 6K8 is rotated out, the DIN-Rail latch is not engaged and the 6K8 can be moved up and out, free of the DIN-Rail mounting..

The picture below is a front / right-side view of a DIN-Rail mounted 6K8. It shows vertical mounting of Magnum 6K8 on a DIN-Rail track for proper convection cooling of the unit. Note that there is air space in the rear, as the 6K8 unit is held out from the rear of the panel by the mounting brackets. The 6K8 design uses the case for cooling (patent pending), and needs to be mounted vertically with air flow space in the front, rear, and sides.

www . GarrettCom . com

26

Image 31
Contents Industrial Field Switch Trademarks Canadian Emission Contacting GarrettCom, IncInstallation Table of ContentsIntroduction Troubleshooting Repeater Port Modules RPMs, 6 types for Ethernet media OverviewMaximum 10 Mbps Ethernet Segment Lengths Technical SpecificationsPerformance Network Standards and Compliance, hardwarePower Supply Internal Fiber Single-mode connector typesAlarm Relay Contacts Management Console connectorAgency Approvals Magnum 6K8 DC Power Supply OptionsPer-port MDI or Mdix on RJ-45 MountingsOrdering Information Configuration OptionsMagnum 6K8 Port Modules GBIC1000Mb Transceiver options for Mangum 6K8-Series Introduction Inspecting the Package and Product Product Description Magnum 6K8-Series 6K8 1a Magnum 6K8-Series, Industrial Field Switch Www . GarrettCom . com Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb Fiber ST or SC Eight-Port Copper Module, 6K8-RJ45Six-Port 4 + 2Combo Modules, 4@ 10/100 RJ-45 and 2@100Mb Fiber4@RJ-45 + 2@ 100MbFour-Port 10 Mb and 100Mb mm Fiber ST Modules Packet Prioritization, 802.1p QOS Gigabit 1000Mbps port modulesFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K8-Series „ Large selection of built-in fiber options at 10/100/1000Mb „ Managed switching for high performance Ethernet LANsApplications Magnum 6K25 Control Center Scada Mounting Instructions Locating Magnum 6K8-Series SwitchesCopper Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock Ieee Standard Media Type Max. Distance Port Module FiberConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InMedia Ieee Standard Twisted Pair CAT 5E 1000BASE-T RJ-45 Www . GarrettCom . com Din-Rail kit Installation procedures Installing DIN-RAIL variable brackets on Magnum 6K8Quantity Description Www . GarrettCom . com Mounting Dimensions for 6K8 with metal brackets Powering the Magnum 6K8-Series Industrial Field Switch 6K8-Series Port Module 6KPMV Installation Stop Preparation for Installing and Removing 6KPMVs from 6K8’sDaughter board Power LED, Pin J5 Power Supply, Pin Dssv 2a a Magnum 6K8 unit with main boardmotherboard only Installing 6KPM Cards in the Magnum 6K8-Series2b Granddaughter Board shown separately Female latch connector6KPMV Cards into a Magnum 6K8-Series Securely latching up Www . GarrettCom . com Enlarged view of Magnum 6K8-Series Console Port area Connecting a Management Console Terminal to Magnum 6K8Retaining screws shown by arrows Remove 6KPM Card Removing a 6KPM Card1 RS-232 DB-9 Console Com port Serial port pin assignments DB-9 Console port connectorFiltering and Forwarding Switching FunctionalityAddress Learning OFF for half duplex Dual LEDs Status on TOP and Front of the 6K8-Series unitAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports On with port activity for 10 Mbps and 100Mbps operationWww . GarrettCom . com Flow-control, Ieee 802.3x Standard ’cvr 6KP4V6KPMV Module Description Introduction Magnum 6K8 Industrial Field Switch Port ModulesDual-mode ST-type connectors 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Connector Www . GarrettCom . com Port@ 100Mbps Multi-Mode Fiber port 5 6KP8-MTRJ, 8 @100Mb multi-mode FX , Mtrj Small-Form-factorCopper and fiber Small Form Factor Mtrj type ports. The small size Mtrj connectors provides anMagnum 6KP8-45MT Module is a combo module with9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port 45-2MT eight port Module is a GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector @ 1000Mb Fiber SC + 2@ 100Mb SC 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC ConnectorBefore Calling for Assistance Return Material Authorization RMA Procedure When Calling for AssistanceNo Problem Found Shipping and Packaging Information Appendix B Internal DC Power Supply OptionsB3.0 B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of OperationB4.0 6K8-SERIES, -48V, 24, 125 or 5VDC Installation B5.0 Operation B4.1 UL Requirements for DC-powered unitsC3.0 DUAL-SOURCE OPTION, Theory of Operation C5.1 UL Requirements C5.0 InstallationExample Magnum 6K8 -24VDC C6.0 Ordering Information Optional
Related manuals
Manual 76 pages 56.37 Kb