GarrettCom Quad-Port Module, RJ-45 copper, Combo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiber

Page 14

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

rather than 100Mb speed. It supports distances according to the 10Base-FL standard, i.e., 2Km distance for multi-mode fiber. (Single-mode for 10km distance may be available as a special order).

2.2.4Quad-Port Module, RJ-45 (copper)

The Magnum Q-Series copper port module, model QPM- RJ45, provides four 10/100Mb switched. RJ-45 ports. The 10/100Mb switched ports are independently N- way auto-negotiating.

 

LK

1

2

3

4

ACT

 

 

 

 

 

x

100/10

 

 

 

FDX/HDX

 

 

 

 

QPM-RJ45

for operation at 10 or 100Mb speed in full- or half-duplex mode (as a default setting). They independently move to half-duplex mode at 10 Mb or at 100Mb speed if the device at the other end of the twisted pair cable is half-duplex or is not an auto-negotiating device.

On the model QPM-RJ45 , there are four LED’s for each port. The LK (Link) indicates “ready for operation” when lit. The ACT (Activity) indicates receiving activity on that port when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF (when auto-negotiation is not disabled). The FDX/HDX LED is ON to indicate full-duplex operation and OFF to indicate half-duplex mode. A twisted pair cable must be connected into each RJ-45 10/100Mb port and a proper Link (LK lit) must be made with the device at the other end of the cable in order for the LEDs to provide valid indications of operating conditions.

Internal jumper settings (See Section 3.4) allow technicians to over-ride the auto-negotiation feature and to manually set each port at full-duplex or half-duplex. One port on each RJ-45 quad-port module is equipped with a Media Dependent Interface- Crossover (MDI-X) push-button switch to simplify cascaded or up-link connections.

2.2.5Combo “3 + 1” Quad Port Modules, 3@RJ-45 and 1@fiber

The combo quad-port modules are combination of copper and fiber media, available as three 10/100 switched RJ-45 copper ports and one 100Mb switched multi- mode fiber ST or SC or single mode SC-type port.

LK 1 2 3 4 ACT

FDX/HDX

 

100/10

FDX/HDX

 

QPRJ-MSC

www . GarrettCom . com

8

Image 14
Contents Fiber Switches Trademarks GarrettCom, Inc Contacting GarrettCom, IncTable of Contents IntroductionIntroduction Magnum QUAD-SERIES QPM Personal Switches, 10/100Mb Personal Hubs, 10Mb seriesTechnical Specifications Agency Approvals Ordering Information Magnum Quad-Series Port ModulesInspecting the Package and Product Product Description Magnum Quad-Series Fiber Switches Magnum Quad-Series chassis modelsPorts Table-Top Fiber Quad-port modules, 100Mb fiberQuad-port modules, 10 Mb QPM-RJ45 Quad-Port Module, RJ-45 copperCombo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiber QPRJ-MSCFrame Buffering and Latency Www . GarrettCom . com „ Front-mounted LEDs, world-wide AC power supply Features and Benefits„ Plug-and-Play installation for high performance switching „ 16-port, 12-port, 8-port and 4-port modelsApplications Example 1 Magnum QS580Example 2 Magnum 8-port QS5108 Example 3 Magnum 16-port QS5116 Locating Magnum Quad-Series Switches Location of 8-port Magnum QS580’s cooling fan exhaustIeee Standard Media Type Max. Distance Port Module Fiber Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock CopperMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Rack-mounting, models QS5108 and QS5116 Table-Top or Shelf MountingWall or Vertical Surface Mounting, 8-port QS580 Multiple Magnum QS5116 units rack-mounted in a 23 frame Jumper Settings for HDX/FDX Fiber ports, internal jumper settings Combo ports, RJ-45 and Fiber internal jumper settings Www . GarrettCom . com Powering the Magnum Quad-Series Switch 10Mbps Fiber ports internal jumper settingsQuad Port Module QPM Installation Preparation for Installing and Removing QPMsRemove Chassis Cover 1a Removing Chassis CoverInstalling QPM Cards in the Magnum Q-Series 1c Front View QPM Retaining Screws hold Face Plates2a Inserting QPM Cards into a Magnum QS5116 Removing QPM Cards 3b Removing a QPM CardAddress Learning Switching FunctionalityFiltering and Forwarding PWR Status LEDsAuto-negotiation, for Fast Ethernet copper ports ACTWww . GarrettCom . com Auto-negotiation for 10 Mb ports, half- or full-duplex mode Flow-control, Ieee 802.3x standardFiber Port Module Introduction Magnum QUAD-SERIES QUAD-PORT Modules QPM Product DescriptionQPM-MST, 100Mb multi-mode FX-ST Quad-port Module, twist lock QPM-SSC 100Mbps single-mode FX-SC-type, snap-in connector 100BASE-FX Single-ModeSmall-form-factor QPM-RJ45 Twisted Pair, 10/100Mb TP Quad-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors QPM-FP 10 Blank Face PlateBefore Calling for Assistance No Problem Found When Calling for AssistanceReturn Material Authorization RMA Procedure Shipping and Packaging Information B1.0 Specifications for Magnum QUAD-SERIES SwitchesPower Supply Internal -48 VDC Option B3.0 Applications for DC Powered Ethernet Switches Power Supply Internal 24 VDC OptionPower Supply Internal 125 or 100VDC Option B5.0 Operation B4.0 InstallationB4.1 UL Requirements B6.0 Ordering Information Magnum QS5116-125VDCC3.0 DUAL-SOURCE OPTION, Theory of Operation C4.0 Features and Benefits of the DUAL-SOURCE DesignC5.0 Installation To the external Terminal BlockExample Magnum QS5116-48VDC C5.1 UL RequirementsC6.0 Ordering Information C7.0 Operation