GarrettCom manual Locating Magnum Quad-Series Switches

Page 21

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

3.0INSTALLATION

Before installing the equipment, it is necessary to take the following precautions:

1.) If the equipment is mounted in an enclosed or multiple rack assembly, the environmental temperature around the equipment must be less than or equal to 500C.

2.) If the equipment is mounted in an enclosed or multiple rack assembly, adequate air flow must be maintained for proper and safe operation.

3.) If the equipment is mounted in an enclosed or multiple rack system placement of the equipment must not overload or load unevenly the rack system.

4.) If the equipment is mounted in an enclosed or multiple rack assembly, verify the equipment’s power requirements to prevent overloading of the building/s electrical circuits.

5.) If the equipment is mounted in an enclosed or multiple rack assembly verify that the equipment has a reliable and uncompromised earthing path.

Installation: This section describes installation of the Magnum Quad-Series Switches, as well as connection of the various Ethernet media types.

3.1Locating Magnum Quad-Series Switches

The location of a Magnum Quad-Series Switch is dependent on the physical

layout of the network. Typically the Switch is placed in a central wiring location where groups of network devices need to be connected in order to communicate with each other. These Switches are typically rack mounted in a wiring closet see Section 3.3.2 below), but because they have rubber feet they can also be installed on a shelf or table top. The compact size of the 8-port QS580 unit allows it to be easily placed in an office or lab area, and it can also be either shelf of wall-mounted (see Section 3.3.1 below).

Locate an AC receptacle that is within six feet (2 meters) of the intended Magnum Quad-Series site. The rugged metal case of the Magnum Quad-Series will normally protect it from accidental damage in a lab or workplace setting. Maintain an open view of the front to visually monitor the status LEDs. Keep an open area around the unit so that cooling can occur from the small fan on the left side, while the unit is in operation. See figure below.

110-220 ON VAC

47-63Hz

1.0-0.5A OFF

FAN EXHAUST

Figure 3.1: Location of 8-port Magnum QS580’s cooling fan exhaust

www . GarrettCom . com

15

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Fiber Switches Trademarks Contacting GarrettCom, Inc GarrettCom, IncIntroduction Table of ContentsIntroduction Magnum QUAD-SERIES QPM Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications Agency Approvals Magnum Quad-Series Port Modules Ordering InformationInspecting the Package and Product Magnum Quad-Series chassis models Product Description Magnum Quad-Series Fiber SwitchesPorts Table-Top Quad-port modules, 100Mb fiber Quad-port modules, 10 MbFiber Combo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiber Quad-Port Module, RJ-45 copperQPM-RJ45 QPRJ-MSCFrame Buffering and Latency Www . GarrettCom . com „ Plug-and-Play installation for high performance switching Features and Benefits„ Front-mounted LEDs, world-wide AC power supply „ 16-port, 12-port, 8-port and 4-port models Example 1 Magnum QS580 ApplicationsExample 2 Magnum 8-port QS5108 Example 3 Magnum 16-port QS5116 Location of 8-port Magnum QS580’s cooling fan exhaust Locating Magnum Quad-Series SwitchesConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Table-Top or Shelf Mounting Wall or Vertical Surface Mounting, 8-port QS580Rack-mounting, models QS5108 and QS5116 Multiple Magnum QS5116 units rack-mounted in a 23 frame Jumper Settings for HDX/FDX Fiber ports, internal jumper settings Combo ports, RJ-45 and Fiber internal jumper settings Www . GarrettCom . com 10Mbps Fiber ports internal jumper settings Powering the Magnum Quad-Series SwitchPreparation for Installing and Removing QPMs Quad Port Module QPM Installation1a Removing Chassis Cover Remove Chassis Cover1c Front View QPM Retaining Screws hold Face Plates Installing QPM Cards in the Magnum Q-Series2a Inserting QPM Cards into a Magnum QS5116 3b Removing a QPM Card Removing QPM CardsSwitching Functionality Filtering and ForwardingAddress Learning Auto-negotiation, for Fast Ethernet copper ports Status LEDsPWR ACTWww . GarrettCom . com Flow-control, Ieee 802.3x standard Auto-negotiation for 10 Mb ports, half- or full-duplex modeFiber Port Module Product Description Introduction Magnum QUAD-SERIES QUAD-PORT Modules QPMQPM-MST, 100Mb multi-mode FX-ST Quad-port Module, twist lock 100BASE-FX Single-Mode QPM-SSC 100Mbps single-mode FX-SC-type, snap-in connectorSmall-form-factor QPM-RJ45 Twisted Pair, 10/100Mb TP Quad-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors 10 Blank Face Plate QPM-FPBefore Calling for Assistance When Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found B1.0 Specifications for Magnum QUAD-SERIES Switches Power Supply Internal -48 VDC OptionShipping and Packaging Information Power Supply Internal 24 VDC Option Power Supply Internal 125 or 100VDC OptionB3.0 Applications for DC Powered Ethernet Switches B4.0 Installation B4.1 UL RequirementsB5.0 Operation Magnum QS5116-125VDC B6.0 Ordering InformationC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC3.0 DUAL-SOURCE OPTION, Theory of Operation To the external Terminal BlockC6.0 Ordering Information C5.1 UL RequirementsExample Magnum QS5116-48VDC C7.0 Operation
Top Page Image Contents