GarrettCom Powering the Magnum Quad-Series Switch, 10Mbps Fiber ports internal jumper settings

Page 30

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

Jumper Settings for 10Mb Fiber Half or Full

 

Jumpe

Port

Functio

Factory

Spee

 

 

 

 

 

 

 

 

 

 

 

JF3

JF 1-2

PIN 1-

FDX @10Mb config

NO

10 Mb

 

 

JF3

JF2-4

Pin 2-4

HDX@10Mb

YE

10 Mb

 

 

JFD1

JP1-3

PIN 1-

FDX@10Mb config

NO

10M

 

 

JFD1

JP2-

PIN 2-

HDX @10Mb config

YE

10M

 

 

 

 

 

 

10Mbps Full

10Mbps Half Duplex

 

JFD

 

JFD

Duplex

 

 

 

 

1

2

1

2

 

3

4

Factory Settings

3

4

 

 

10Mbps Half-

 

 

10Mbps Full-

 

Duplex

 

 

Duplex

 

JFD

Jumper Settings for HDX/FDX

JF3

JF3

Factory Settings

1

2

 

10

10

 

Printed Circuit card Bottom QPM Retaining

Two(50) Pin

4PM Connectors (inserts into main board )

Jumper Settings for HDX/FDX

JF

1 2

34

5

Figure 3.7 10Mbps Fiber ports internal jumper settings.

Note: Be certain that the main power is disconnected before opening the unit or changing any internal jumper settings

3.8Powering the Magnum Quad-Series Switch

The Magnum Quad-Series Switches incorporate an internal universal power

supply, and has a recessed male IEC connector for the AC power cord at the left-rear. A manual power ON-OFF switch is adjacent. A six-foot 115 VAC 60 Hz standard power cord is supplied with each unit shipped within the United States and Canada.

110-220

ON

VAC

 

47-63Hz

1.0-0.5A OFF

Figure 3.5: Magnum Quad- Series AC power connector

The auto-ranging power supply supports installation environments where the AC voltage is from 90 to 260 volts with a power input frequency of between 47 and 63 Hz. The 8-port units will consume just under 20 watts of power typically, and the 16- port units will consume about 35 watts typically.

www . GarrettCom . com

24

Image 30
Contents Fiber Switches Trademarks GarrettCom, Inc Contacting GarrettCom, IncTable of Contents IntroductionIntroduction Magnum QUAD-SERIES QPM Personal Switches, 10/100Mb Personal Hubs, 10Mb seriesTechnical Specifications Agency Approvals Ordering Information Magnum Quad-Series Port ModulesInspecting the Package and Product Product Description Magnum Quad-Series Fiber Switches Magnum Quad-Series chassis modelsPorts Table-Top Quad-port modules, 100Mb fiber Quad-port modules, 10 MbFiber QPM-RJ45 Quad-Port Module, RJ-45 copperCombo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiber QPRJ-MSCFrame Buffering and Latency Www . GarrettCom . com „ Front-mounted LEDs, world-wide AC power supply Features and Benefits„ Plug-and-Play installation for high performance switching „ 16-port, 12-port, 8-port and 4-port modelsApplications Example 1 Magnum QS580Example 2 Magnum 8-port QS5108 Example 3 Magnum 16-port QS5116 Locating Magnum Quad-Series Switches Location of 8-port Magnum QS580’s cooling fan exhaustIeee Standard Media Type Max. Distance Port Module Fiber Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Table-Top or Shelf Mounting Wall or Vertical Surface Mounting, 8-port QS580Rack-mounting, models QS5108 and QS5116 Multiple Magnum QS5116 units rack-mounted in a 23 frame Jumper Settings for HDX/FDX Fiber ports, internal jumper settings Combo ports, RJ-45 and Fiber internal jumper settings Www . GarrettCom . com Powering the Magnum Quad-Series Switch 10Mbps Fiber ports internal jumper settingsQuad Port Module QPM Installation Preparation for Installing and Removing QPMsRemove Chassis Cover 1a Removing Chassis CoverInstalling QPM Cards in the Magnum Q-Series 1c Front View QPM Retaining Screws hold Face Plates2a Inserting QPM Cards into a Magnum QS5116 Removing QPM Cards 3b Removing a QPM CardSwitching Functionality Filtering and ForwardingAddress Learning PWR Status LEDsAuto-negotiation, for Fast Ethernet copper ports ACTWww . GarrettCom . com Auto-negotiation for 10 Mb ports, half- or full-duplex mode Flow-control, Ieee 802.3x standardFiber Port Module Introduction Magnum QUAD-SERIES QUAD-PORT Modules QPM Product DescriptionQPM-MST, 100Mb multi-mode FX-ST Quad-port Module, twist lock QPM-SSC 100Mbps single-mode FX-SC-type, snap-in connector 100BASE-FX Single-ModeSmall-form-factor QPM-RJ45 Twisted Pair, 10/100Mb TP Quad-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors QPM-FP 10 Blank Face PlateBefore Calling for Assistance When Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found B1.0 Specifications for Magnum QUAD-SERIES Switches Power Supply Internal -48 VDC OptionShipping and Packaging Information Power Supply Internal 24 VDC Option Power Supply Internal 125 or 100VDC OptionB3.0 Applications for DC Powered Ethernet Switches B4.0 Installation B4.1 UL RequirementsB5.0 Operation B6.0 Ordering Information Magnum QS5116-125VDCC3.0 DUAL-SOURCE OPTION, Theory of Operation C4.0 Features and Benefits of the DUAL-SOURCE DesignC5.0 Installation To the external Terminal BlockExample Magnum QS5116-48VDC C5.1 UL RequirementsC6.0 Ordering Information C7.0 Operation