GarrettCom Quad Connecting Ethernet Media, Connecting Fiber Optic ST-type, twist-lock, Copper

Page 22

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

3.2Connecting Ethernet Media

The Magnum Quad-Series Fiber Switches are specifically designed to support all standard Ethernet media types within a single Switch unit. This is accomplished by using a family of Quad-port Modules (QPMs) which can be individually selected and configured per-port. See Section 2.4 for a description of the QPMs.

The various media types supported along with the corresponding IEEE

802.3 and 802.3u standards and connector types are as follows:

IEEE Standard

Media Type

Max. Distance

Port Module

Fiber:

mm1 Fiber

2.0km (6,562 ft)

 

100BASE-FX

QPM-MSC, -MST

 

sgl.m2 Fiber

18.0km (95K ft)

QPM-SSC

small form factor

mm1 Fiber

2.0km (6,562 ft)

QPM-MTRJ, -MV45

10BASE-FL

mm1 Fiber

2.0km(6,562 ft)

QPM10-FST

Copper:

 

 

10BASE-T & 100BASE-TX twisted pair 100m (328 ft)

QPM-RJ45

1 mm = multi-mode

2 sgl.m = single-mode

3.2.1Connecting Fiber Optic ST-type, “twist-lock”

The following procedure applies to installations using a QPM with ST-type fiber connectors. This procedure applies to ports using a QPM-MST or QPM10-MST.

1.Before connecting the fiber optic cable, remove the protective dust caps from the tips of the connectors on the QPM. Save these dust caps for future use.

2.Wipe clean the ends of the dual connectors with a soft cloth or lint-free lens tissue dampened in alcohol. Make certain the connectors are clean before connecting.

Note: One strand of the duplex fiber optic cable is coded using color bands at regular intervals; you must use the color-coded strand on the associated ports at each end of the fiber optic segment.

3.Connect the Transmit (TX) port (light colored post) on the Magnum QPM to the Receive (RX) port of the remote device. Begin with the color-coded strand of the cable for this first TX-to-RX connection.

4.Connect the Receive (RX) port (dark colored post on the PM) to the Transmit (TX) port of the remote device. Use the non-color coded fiber strand for this.

5.The LINK LED on the front of the QPM will illuminate when a proper connection has been established at both ends (and when power is ON in the unit). If LINK is not lit after cable connection, the normal cause is improper cable polarity. Swap the fiber cables at the QPM connector to remedy this situation.

www. GarrettCom . com

16

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Fiber Switches Trademarks GarrettCom, Inc Contacting GarrettCom, IncTable of Contents IntroductionIntroduction Magnum QUAD-SERIES QPM Personal Switches, 10/100Mb Personal Hubs, 10Mb seriesTechnical Specifications Agency Approvals Ordering Information Magnum Quad-Series Port ModulesInspecting the Package and Product Product Description Magnum Quad-Series Fiber Switches Magnum Quad-Series chassis modelsPorts Table-Top Quad-port modules, 10 Mb Quad-port modules, 100Mb fiberFiber QPM-RJ45 Quad-Port Module, RJ-45 copperCombo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiber QPRJ-MSCFrame Buffering and Latency Www . GarrettCom . com „ Front-mounted LEDs, world-wide AC power supply Features and Benefits„ Plug-and-Play installation for high performance switching „ 16-port, 12-port, 8-port and 4-port modelsApplications Example 1 Magnum QS580Example 2 Magnum 8-port QS5108 Example 3 Magnum 16-port QS5116 Locating Magnum Quad-Series Switches Location of 8-port Magnum QS580’s cooling fan exhaustIeee Standard Media Type Max. Distance Port Module Fiber Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InMedia Ieee Standard Wall or Vertical Surface Mounting, 8-port QS580 Table-Top or Shelf MountingRack-mounting, models QS5108 and QS5116 Multiple Magnum QS5116 units rack-mounted in a 23 frame Jumper Settings for HDX/FDX Fiber ports, internal jumper settings Combo ports, RJ-45 and Fiber internal jumper settings Www . GarrettCom . com Powering the Magnum Quad-Series Switch 10Mbps Fiber ports internal jumper settingsQuad Port Module QPM Installation Preparation for Installing and Removing QPMsRemove Chassis Cover 1a Removing Chassis CoverInstalling QPM Cards in the Magnum Q-Series 1c Front View QPM Retaining Screws hold Face Plates2a Inserting QPM Cards into a Magnum QS5116 Removing QPM Cards 3b Removing a QPM CardFiltering and Forwarding Switching FunctionalityAddress Learning PWR Status LEDsAuto-negotiation, for Fast Ethernet copper ports ACTWww . GarrettCom . com Auto-negotiation for 10 Mb ports, half- or full-duplex mode Flow-control, Ieee 802.3x standardFiber Port Module Introduction Magnum QUAD-SERIES QUAD-PORT Modules QPM Product DescriptionQPM-MST, 100Mb multi-mode FX-ST Quad-port Module, twist lock QPM-SSC 100Mbps single-mode FX-SC-type, snap-in connector 100BASE-FX Single-ModeSmall-form-factor QPM-RJ45 Twisted Pair, 10/100Mb TP Quad-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors QPM-FP 10 Blank Face PlateBefore Calling for Assistance Return Material Authorization RMA Procedure When Calling for AssistanceNo Problem Found Power Supply Internal -48 VDC Option B1.0 Specifications for Magnum QUAD-SERIES SwitchesShipping and Packaging Information Power Supply Internal 125 or 100VDC Option Power Supply Internal 24 VDC OptionB3.0 Applications for DC Powered Ethernet Switches B4.1 UL Requirements B4.0 InstallationB5.0 Operation B6.0 Ordering Information Magnum QS5116-125VDCC3.0 DUAL-SOURCE OPTION, Theory of Operation C4.0 Features and Benefits of the DUAL-SOURCE DesignC5.0 Installation To the external Terminal BlockExample Magnum QS5116-48VDC C5.1 UL RequirementsC6.0 Ordering Information C7.0 Operation
Top Page Image Contents