GarrettCom Quad manual Installing QPM Cards in the Magnum Q-Series

Page 33

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

Step 3. Remove bottom-front and modules rear top Retaining Screws in any QPM or Face Plates

On the bottom-front of the unit, there are two retaining screws for each QPM card slot as well as two other retaining screws on the rear top of the module. These four screws are used to secure a QPM face plate in position. These screws are also used to secure the individual QPM cards, which can be subjected to significant forces from the attached cables. (See Figure 3.9.1c)

MagnumQS5116

Fiber Switch

TwoBottomretainingScrews for eachQPMcard

Two retaining screws on the rear top of module

QPM CARDS

J1 J2 J3

Printed CircJ4uit card

TOP

Magnum QS5116

Fiber Switch

GARRETT

Figure 3.9.1c: Front View - QPM Retaining Screws hold Face Plates

3.9.2Installing QPM Cards in the Magnum Q-Series

Up to four front-mounted QPM cards may be installed in one Magnum 5116 Fiber switch unit. Follow these steps to install a QPM.

Step 1. Remove top chassis cover. See procedure in Section 3.9.1 above.

Step 2. Screw down tightly the two 7/16 stand-off on the top of pre installed stand-off from the factory.

Step 3. Align the two headers pin on the top of the two sets of socket fixed at the bottom side of the QPM module. (Note: After firmly attached the sockets and the header pin, move the mounted pins slightly tilted towards the front of the chassis.

 

 

 

 

Jumper Settings for HDX/FDX

Step 4. The figure here

 

 

 

and Auto Negotiation

 

 

 

 

 

illustrates the basic

 

J1

J2

J3

J4

 

Printed Circuit card

 

Two Set of Ten(10) Pin

layout of an

 

 

 

 

QPM Connector

 

TOP

 

 

(inserts into main board)

individual QPM

Uplink

 

LED

 

 

 

 

 

 

card. Each QPM

Switch

 

 

 

 

 

 

 

 

 

card fits into the

 

FRONT

 

 

 

 

 

 

 

 

selected QPM connector socket slot. Align the connector pins on the bottom of the QPM card with the connector socket inside the unit.

www . GarrettCom . com

27

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Fiber Switches Trademarks Contacting GarrettCom, Inc GarrettCom, IncIntroduction Table of ContentsIntroduction Magnum QUAD-SERIES QPM Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications Agency Approvals Magnum Quad-Series Port Modules Ordering InformationInspecting the Package and Product Magnum Quad-Series chassis models Product Description Magnum Quad-Series Fiber SwitchesPorts Table-Top Quad-port modules, 100Mb fiber Quad-port modules, 10 MbFiber Combo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiber Quad-Port Module, RJ-45 copperQPM-RJ45 QPRJ-MSCFrame Buffering and Latency Www . GarrettCom . com „ Plug-and-Play installation for high performance switching Features and Benefits„ Front-mounted LEDs, world-wide AC power supply „ 16-port, 12-port, 8-port and 4-port modelsExample 1 Magnum QS580 ApplicationsExample 2 Magnum 8-port QS5108 Example 3 Magnum 16-port QS5116 Location of 8-port Magnum QS580’s cooling fan exhaust Locating Magnum Quad-Series SwitchesConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Table-Top or Shelf Mounting Wall or Vertical Surface Mounting, 8-port QS580Rack-mounting, models QS5108 and QS5116 Multiple Magnum QS5116 units rack-mounted in a 23 frame Jumper Settings for HDX/FDX Fiber ports, internal jumper settings Combo ports, RJ-45 and Fiber internal jumper settings Www . GarrettCom . com 10Mbps Fiber ports internal jumper settings Powering the Magnum Quad-Series SwitchPreparation for Installing and Removing QPMs Quad Port Module QPM Installation1a Removing Chassis Cover Remove Chassis Cover1c Front View QPM Retaining Screws hold Face Plates Installing QPM Cards in the Magnum Q-Series2a Inserting QPM Cards into a Magnum QS5116 3b Removing a QPM Card Removing QPM CardsSwitching Functionality Filtering and ForwardingAddress Learning Auto-negotiation, for Fast Ethernet copper ports Status LEDsPWR ACTWww . GarrettCom . com Flow-control, Ieee 802.3x standard Auto-negotiation for 10 Mb ports, half- or full-duplex modeFiber Port Module Product Description Introduction Magnum QUAD-SERIES QUAD-PORT Modules QPMQPM-MST, 100Mb multi-mode FX-ST Quad-port Module, twist lock 100BASE-FX Single-Mode QPM-SSC 100Mbps single-mode FX-SC-type, snap-in connectorSmall-form-factor QPM-RJ45 Twisted Pair, 10/100Mb TP Quad-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors 10 Blank Face Plate QPM-FPBefore Calling for Assistance When Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found B1.0 Specifications for Magnum QUAD-SERIES Switches Power Supply Internal -48 VDC OptionShipping and Packaging Information Power Supply Internal 24 VDC Option Power Supply Internal 125 or 100VDC OptionB3.0 Applications for DC Powered Ethernet Switches B4.0 Installation B4.1 UL RequirementsB5.0 Operation Magnum QS5116-125VDC B6.0 Ordering InformationC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC3.0 DUAL-SOURCE OPTION, Theory of Operation To the external Terminal BlockC6.0 Ordering Information C5.1 UL RequirementsExample Magnum QS5116-48VDC C7.0 Operation
Top Page Image Contents