GarrettCom Quad manual Remove Chassis Cover, 1a Removing Chassis Cover

Page 32

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

Step 2. Remove Chassis Cover

The Magnum Q-Series chassis are combined with top and bottom part and assembled together with the help of 20 Philips head screws. There are 7 screws located on front-top of the unit and three screws each on the left and right edges. Remove these screws. Once these are removed, the top cover is easily lifted off the chassis base. When the chassis top cover has been removed, the interior of the unit is exposed.

20 Phillips Head Screws on Top

TopChassis Cover

Magnum QS5116

Fiber Switch

GARRETT

Figure 3.9.1a: Removing Chassis Cover

Caution: Be careful not to disturb the power supply.

Looking down into the Magnum Q-Series unit, notice that there are individual QPM connector sockets along with two stand-offs for each QPM card position. There are four QPM slots located on the front of the QS5116 model, whereas QS580 and QS5108 has two QPM slots in the front. (See Figure 3.9.1b).

AC Power Input

Back of Unit

Cooling Fan

Left

Side

LED Status Slot

Power Supply Board

Right

Side

Eight QPM Slots

Front of Unit

Figure 3.9.1b: Magnum QS5116, Top View with Chassis Cover

www . GarrettCom . com

26

Image 32

Contents Fiber Switches Trademarks GarrettCom, Inc Contacting GarrettCom, IncTable of Contents IntroductionIntroduction Magnum QUAD-SERIES QPM Personal Switches, 10/100Mb Personal Hubs, 10Mb seriesTechnical Specifications Agency Approvals Ordering Information Magnum Quad-Series Port ModulesInspecting the Package and Product Product Description Magnum Quad-Series Fiber Switches Magnum Quad-Series chassis modelsPorts Table-Top Fiber Quad-port modules, 100Mb fiberQuad-port modules, 10 Mb Quad-Port Module, RJ-45 copper Combo 3 + 1 Quad Port Modules, 3@RJ-45 and 1@fiberQPM-RJ45 QPRJ-MSCFrame Buffering and Latency Www . GarrettCom . com Features and Benefits „ Plug-and-Play installation for high performance switching„ Front-mounted LEDs, world-wide AC power supply „ 16-port, 12-port, 8-port and 4-port modelsApplications Example 1 Magnum QS580Example 2 Magnum 8-port QS5108 Example 3 Magnum 16-port QS5116 Locating Magnum Quad-Series Switches Location of 8-port Magnum QS580’s cooling fan exhaustConnecting Ethernet Media Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Rack-mounting, models QS5108 and QS5116 Table-Top or Shelf MountingWall or Vertical Surface Mounting, 8-port QS580 Multiple Magnum QS5116 units rack-mounted in a 23 frame Jumper Settings for HDX/FDX Fiber ports, internal jumper settings Combo ports, RJ-45 and Fiber internal jumper settings Www . GarrettCom . com Powering the Magnum Quad-Series Switch 10Mbps Fiber ports internal jumper settingsQuad Port Module QPM Installation Preparation for Installing and Removing QPMsRemove Chassis Cover 1a Removing Chassis CoverInstalling QPM Cards in the Magnum Q-Series 1c Front View QPM Retaining Screws hold Face Plates2a Inserting QPM Cards into a Magnum QS5116 Removing QPM Cards 3b Removing a QPM CardAddress Learning Switching FunctionalityFiltering and Forwarding Status LEDs Auto-negotiation, for Fast Ethernet copper portsPWR ACTWww . GarrettCom . com Auto-negotiation for 10 Mb ports, half- or full-duplex mode Flow-control, Ieee 802.3x standardFiber Port Module Introduction Magnum QUAD-SERIES QUAD-PORT Modules QPM Product DescriptionQPM-MST, 100Mb multi-mode FX-ST Quad-port Module, twist lock QPM-SSC 100Mbps single-mode FX-SC-type, snap-in connector 100BASE-FX Single-ModeSmall-form-factor QPM-RJ45 Twisted Pair, 10/100Mb TP Quad-Port 10/100BASE-T and 100BASE-FX Combo Quad-Port Connectors QPM-FP 10 Blank Face PlateBefore Calling for Assistance No Problem Found When Calling for AssistanceReturn Material Authorization RMA Procedure Shipping and Packaging Information B1.0 Specifications for Magnum QUAD-SERIES SwitchesPower Supply Internal -48 VDC Option B3.0 Applications for DC Powered Ethernet Switches Power Supply Internal 24 VDC OptionPower Supply Internal 125 or 100VDC Option B5.0 Operation B4.0 InstallationB4.1 UL Requirements B6.0 Ordering Information Magnum QS5116-125VDCC4.0 Features and Benefits of the DUAL-SOURCE Design C5.0 InstallationC3.0 DUAL-SOURCE OPTION, Theory of Operation To the external Terminal BlockC5.1 UL Requirements C6.0 Ordering InformationExample Magnum QS5116-48VDC C7.0 Operation