GE CBR-PB3-WD installation manual Detailed Installation Steps, PB3 Physical Installation

Page 13

5 Detailed Installation

Steps

5.1PB3 Physical Installation

1.Disconnect the existing Receipt Printer cable from the back of the POS system and install the ECR Interconnect Cable (4310-0078A) to the Receipt Printer as shown on page 11.

2.Reconnect the Receipt Printer Cable to one of the D9F connectors on the ECR Interconnect Cable as shown

on page 11.

3.Connect the other end (DB9F) to the DB9M connector on the PB3 unit.

4.Connect the PB3 Power Supply to the unit.

If only one (1) PB3 unit (one cash register) is to be connected, skip to Step 8 below.

5.If more than one cash register interface is to be installed repeat steps 1- 4 above for each additional cash register.

6.Connect each PB3 unit together by using an RS-485 cable with RJ-45 connectors on each end. Connect to either receptacle on Port 0 to interconnect the PB3 units using an “in” and “out” method. (For details on the RS-485 cable, review the cable specifications in Section 13).

Note: This cable shall be provided by the installer.

7.Confirm that each PB3 has the proper termination setting per the instructions on page 12.

8.Connect all ECR cameras to their associated inputs on the DVMRe unit (ECR#1 = Camera 1 Input, ECR#2 = Camera 2 Input….)

9.Connect the PB3 closest to the DVMRe using the supplied cable (4310- 0043B) from Port 1 (RJ45 outer receptacle) of the PB3 to the RS232/2 port on the DVMRe unit.

Kalatel CBR-PB3-WD

13

0150-0261A

Image 13
Contents Kalatel CBR-PB3-WD ProBridge Receipt Printer Interface Copyright Information Table of Contents 14.1 Factory Service 14.2 Warranty Cable Specifications Warranty and ServiceCBR-PB3-WD ProBridge Additional Equipment Provided by InstallerKalatel CBR-PB3-WD Description CompatibilityHow to Use this Manual Installation SummaryBefore You Begin Kalatel ComponentsPower Installation Environment4310-0007 120VAC Power Supply Tolerance ±10% Frequency 50 Hz Power Supply Output 4310-0008 220VAC Power SupplyProBridge Diagram Important Switch Assignments Default Factory Dipswitch SettingsDVMRe Triplex Connection DiagramSample Systems Termination Termination SwitchPB3 Physical Installation Detailed Installation StepsAssociating ECR data to a specific camera Configuring the PB3 for POS InterfaceProcess several POS transactions at the Cash Register Kalatel CBR-PB3-WD 0150-0261A Special Functions Demo Simulated Message ModeDisplay Memory Reset Clear Memory Kalatel CBR-PB3-WD 0150-0261A Switch Setting TroubleshootingUp Off = U Down On = D Baud Rate Port 1200 2400 4800 9600 14.4k 19.2k 38.4kTroubleshooting Guide Dipswitch 5 Camera Assignment Dipswitch Numbers SW1 DipswitchesText to Camera Address SW1 Manual Dipswitch Settings Available Manual Switch ConfigBaud Rate Protocol Kalatel CBR-PB3-WD 0150-0261A Equipment Required HyperTerminal SetupSetting up the ProBridge for HyperTerminal Operation Manual HyperTerminal Configuration Menu Selection 2 Protocol Options q Asynchronous Setup Option 2 Port #2Menu Selection 3 Baud Rate Menu Selection 5 Mode The available selections areMenu Selection 4 Parity Menus Selection 7 Device Type q Generic Receipt Printer11 PB3-POS with DVMRe -CD/CS Units DVMRe-CS/CD SetupCommunicationsRS-232Port 1 ATM Activate Final Testing RJ-45 Connector Cable SpecificationsRJ-45 Connector DB9F Connector ProBridge to Triplex DVMRe-CTRJ45 Connector Communication Type RS-485 Connector Type RJ45, RJ45DB9F Connector DB9F and DB9M Connector ProBridge to ProBridge CableSpecifications Factory Service Warranty and ServiceWarranty Factory AddressAdvance Replacement Policy