GE CBR-PB3-WD Configuring the PB3 for POS Interface, Associating ECR data to a specific camera

Page 14

5.2Configuring the PB3 for POS Interface

1.Associating ECR data to a specific camera.

Dipswitches 5-8on SW1 are used for assigning an

ECR’s transaction text to a specific camera.

Please refer to Section 8 for the specific dipswitch camera assignments. The default setting is for switches 5-8 to be all OFF (All switches Up = Camera 1).

2.Program the DVMRe for the desired recording functions based upon the presence of transaction text. In addition make sure the RS-232 port on the DVMRe is configured correctly set via the DVMRe Setup Menus:

a.COMMUNICATIONS>RS-232>PORT (1 OR 2)>19200

i.Port 2 is used if DVMRe-CT/eZT/StoreSafe

ii.Port 1 is used if DVMRe-CS/CD/eZ

NOTE

Transaction text is captured with video regardless of the recording mode (Time-Lapse, Time-Lapse + Event, or Event Only). If Time-Lapse + Event or Event Only recording modes must have at least one (1) second set for the pre- event duration.

3.Process several POS transactions at the Cash Register.

a.To verify proper operation with a DVMRe-CT/eZT/StoreSafe unit:

i.Select full-screen on the Main Monitor (A) the camera associated with a PB3 unit. Press the camera button until the text box window appears in the display.

ii.The text box will display any transaction data as it is passed to the PB3 unit from the POS device. Be aware that some POS devices only send transaction data until the end of the transaction (when the receipt is printed).

Kalatel CBR-PB3-WD

14

0150-0261A

Image 14
Contents Kalatel CBR-PB3-WD ProBridge Receipt Printer Interface Copyright Information Table of Contents Cable Specifications Warranty and Service 14.1 Factory Service 14.2 WarrantyKalatel CBR-PB3-WD Description Additional Equipment Provided by InstallerCBR-PB3-WD ProBridge CompatibilityBefore You Begin Installation SummaryHow to Use this Manual Kalatel Components4310-0007 120VAC Power Supply Installation EnvironmentPower 4310-0008 220VAC Power Supply Tolerance ±10% Frequency 50 Hz Power Supply OutputProBridge Diagram Default Factory Dipswitch Settings Important Switch AssignmentsConnection Diagram DVMRe TriplexTermination Switch Sample Systems TerminationDetailed Installation Steps PB3 Physical InstallationProcess several POS transactions at the Cash Register Configuring the PB3 for POS InterfaceAssociating ECR data to a specific camera Kalatel CBR-PB3-WD 0150-0261A Display Memory Demo Simulated Message ModeSpecial Functions Reset Clear Memory Kalatel CBR-PB3-WD 0150-0261A Up Off = U Down On = D TroubleshootingSwitch Setting Baud Rate Port 1200 2400 4800 9600 14.4k 19.2k 38.4kTroubleshooting Guide Text to Camera Address SW1 DipswitchesDipswitch 5 Camera Assignment Dipswitch Numbers SW1 Baud Rate Manual Switch ConfigManual Dipswitch Settings Available Protocol Kalatel CBR-PB3-WD 0150-0261A HyperTerminal Setup Equipment RequiredSetting up the ProBridge for HyperTerminal Operation Manual HyperTerminal Configuration Setup Option 2 Port #2 Menu Selection 2 Protocol Options q AsynchronousMenu Selection 4 Parity Menu Selection 5 Mode The available selections areMenu Selection 3 Baud Rate Menus Selection 7 Device Type q Generic Receipt PrinterCommunicationsRS-232Port 1 ATM Activate DVMRe-CS/CD Setup11 PB3-POS with DVMRe -CD/CS Units Final Testing RJ-45 Connector DB9F Connector Cable SpecificationsRJ-45 Connector ProBridge to Triplex DVMRe-CTDB9F Connector DB9F and DB9M Connector Communication Type RS-485 Connector Type RJ45, RJ45RJ45 Connector ProBridge to ProBridge CableSpecifications Warranty Warranty and ServiceFactory Service Factory AddressAdvance Replacement Policy