GE CBR-PB3-WD installation manual Protocol

Page 24

9.1.2Protocol

	Legend: Up (Off) = U	Down (On) = D

					SW2
				Switch Setting

			5		6		7	8

q	Protocol: Asynchronous
q	Parity: Even		U		D		U	D
q Code: 8-Bit ASCII			U		D		U	D
q Code: 8-Bit ASCII
q Mode: 1 Stop Bit

q	Protocol: Asynchronous
q	Parity: Odd		U		D		U	U
q Code: 8-Bit ASCII			U		D		U	U
q Code: 8-Bit ASCII
q Mode: 1 Stop Bit

q	Protocol: Asynchronous
q	Parity: None		U		U		D	D
q Code: 8-Bit ASCII			U		U		D	D
q Code: 8-Bit ASCII
q Mode: 1 Stop Bit

q	Protocol: Asynchronous
q	Parity: Even		U		U		D	U
q Code: 7-Bit ASCII			U		U		D	U
q Code: 7-Bit ASCII
q Mode: 1 Stop Bit

q	Protocol: Asynchronous
q	Parity: Odd		U		U		U	D
q Code: 7-Bit ASCII			U		U		U	D
q Code: 7-Bit ASCII
q Mode: 1 Stop Bit

q	Protocol: Asynchronous
q	Parity: None		U		U		U	U
q Code: 7-Bit ASCII			U		U		U	U
q Code: 7-Bit ASCII
q Mode: 1 Stop Bit

Kalatel CBR-PB3-WD

24

0150-0261A

Image 24

Contents Kalatel CBR-PB3-WD ProBridge Receipt Printer Interface Copyright Information Table of Contents Cable Specifications Warranty and Service 14.1 Factory Service 14.2 WarrantyAdditional Equipment Provided by Installer CBR-PB3-WD ProBridgeKalatel CBR-PB3-WD Description CompatibilityInstallation Summary How to Use this ManualBefore You Begin Kalatel ComponentsInstallation Environment Power4310-0007 120VAC Power Supply 4310-0008 220VAC Power Supply Tolerance ±10% Frequency 50 Hz Power Supply OutputProBridge Diagram Default Factory Dipswitch Settings Important Switch AssignmentsConnection Diagram DVMRe TriplexTermination Switch Sample Systems TerminationDetailed Installation Steps PB3 Physical InstallationConfiguring the PB3 for POS Interface Associating ECR data to a specific cameraProcess several POS transactions at the Cash Register Kalatel CBR-PB3-WD 0150-0261A Demo Simulated Message Mode Special FunctionsDisplay Memory Reset Clear Memory Kalatel CBR-PB3-WD 0150-0261A Troubleshooting Switch SettingUp Off = U Down On = D Baud Rate Port 1200 2400 4800 9600 14.4k 19.2k 38.4kTroubleshooting Guide SW1 Dipswitches Dipswitch 5 Camera Assignment Dipswitch NumbersText to Camera Address SW1 Manual Switch Config Manual Dipswitch Settings AvailableBaud Rate Protocol Kalatel CBR-PB3-WD 0150-0261A HyperTerminal Setup Equipment RequiredSetting up the ProBridge for HyperTerminal Operation Manual HyperTerminal Configuration Setup Option 2 Port #2 Menu Selection 2 Protocol Options q AsynchronousMenu Selection 5 Mode The available selections are Menu Selection 3 Baud RateMenu Selection 4 Parity Menus Selection 7 Device Type q Generic Receipt PrinterDVMRe-CS/CD Setup 11 PB3-POS with DVMRe -CD/CS UnitsCommunicationsRS-232Port 1 ATM Activate Final Testing Cable Specifications RJ-45 ConnectorRJ-45 Connector DB9F Connector ProBridge to Triplex DVMRe-CTCommunication Type RS-485 Connector Type RJ45, RJ45 RJ45 ConnectorDB9F Connector DB9F and DB9M Connector ProBridge to ProBridge CableSpecifications Warranty and Service Factory ServiceWarranty Factory AddressAdvance Replacement Policy