GE GEK 106168E manual Breaker Setting Group, Active table setting group

Page 24

3. SETTINGS

3.SETTINGS

This section describes the settings of the DBF relay and the procedure to modify them. Table 3 shows the list of DBF settings, their range and resolution, and the factory default settings.

To view or to modify settings using the GE_LOCAL program connected to PORT 1, PORT 2 or PORT 3 the user has to perform the following steps:

∙Check that the available connection cable is in accordance with the diagram in Figure 7. Check correspondence between DB-9 connector in the cable with available connector at PC port (could be DB-9 or DB-25)

∙Connect the cable between the relay (or modem) and the serial port of your computer.

∙Run the GE-LOCAL software. For more details on the installation and use of the GE-LOCAL software see instruction book GEK-105568.

∙Make sure that the communication parameters in GE_LOCAL match with those set on the DBF. Specifically, the parameters on the configuration of the local HMI are:

∗COMMUNICATION SPEED: On the relay depending on whether communication is: through PORT 1 or PORT 2 (means LOCAL), or PORT 3 (means NET)

∗STOP BIT: Stop-bit corresponding to each one of the communication ways: LOCAL or

NET

To modify or view the DBF communication parameters refer to Chapter 8, Section 8.1 “Menu Tree”.

IMPORTANT: It should be noted that in order to simplify the setting of the unit and for safety reasons, all settings related with the configuration of the unit (configurable inputs and outputs, internal status events and target LED’s) have been removed from the HMI facilities and also from the communications software GE_LOCAL. To perform these configurations the GE_INTRO software (described in instruction book GEK-105569) must be used.

TABLE 3. Settings Table

Common to all tables	Range	Default	Step
	General Settings Group
Relay status	In/out of service	In-service
Identification	20 ASCII characters	No ID
Frequency	50 / 60 Hz	50 Hz
Phase CT Ratio	1-4000	1	1
Neutral CT Ratio	1-4000	1	1

Breaker Setting Group

Breaker Number	4 ASCII characters		0000
kI2t Operation Mode	Fixed-Measured		Fixed
Integration Time for kI2t	0.03-0.25s		0.06s	0.01s
kI2t Maximum Limit	1-999999		99999	1

	Active table setting group
Active setting table #	1 - 3		1	1

GEK-106168E

DBF Breaker Failure Protection

17

Image 24

Contents GE Power Management 3KRQHHVFULSWLRQ0DQXDO*RI.\RXUFRGHTXHVWLRQ Ruvxjjhvwlrqd Page Table of Contents Installation and Maintenance List of Figures Rear View 226B7412 SheetDBF Breaker Failure Protection GEK-106168E General Description Protection∙ Breaker internal arc detection Monitoring AnalysisDBF Breaker Failure Protection GEK-106168E Digital Signal Input # Terminals Protection FunctionsOvercurrent Units Low-Level Overcurrent Breaker Failure Unit 50BF 1PReset of Latching Relays Ground Overcurrent Breaker Failure UnitBreaker Failure without current or very low current Breaker Arc Detection DeviceInternal Protection Status Signals Monitoring and Recording FunctionsMeasurement Associated Breaker StatusGroup Status Comment Optional Exp. Board Optional Exp. Board Latched#1 ClosedOptional Exp.Boar Latched#2 Closed Internal Communication Status Signals LED Left Column Right Column Circuit Breaker Breaking Capacity MonitoringAnalysis Functions BUILT-IN SELF-CHECKING UnitEvent Recorder OscillographyEvents to Trigger Oscillography Tables of Settings ControlTable Selection Active Table INPUT-1 INPUT-0Configurable Inputs and Outputs Time SynchronizationFunction Outputs MAN-MACHINE Interface HMI Remote Communications Breaker Setting Group Active table setting groupCommon to all tables Range Default Step Oscillography Mask Independent for each table Range Default Step 50BF SettingsInternal Arc Settings Functions PermittedComments on Settings DBF Breaker Failure Protection GEK-106168E Ranges Models DBF Phase Model ListDBF GroundTechnical Characteristics MechanicalElectrical Communications StandardsTest Standard Class DBF Breaker Failure Protection GEK-106168E Physical Description CaseElectrical Connections Internal ConstructionDBF Breaker Failure Protection GEK-106168E Operating Theory Magnetic ModuleCPU Board Power Supply Keyboard and DisplayConnections and Necessary Equipment Visual InspectionPanel Insulation Tests Relay Setting IndicatorsPower Supply Communications Inputs Digital InputsIRIG-B Synchronizing Input Functions 1 50BF 1P Unit Test2 50BF 3P Unit Test Internal ARC Test 4 3P no I FunctionNeutral Overcurrent Unit Test DBF Breaker Failure Protection GEK-106168E Relay Measurement Tests Current MeasurementTiming Measurement DBF Breaker Failure Protection GEK-106168E Installation MaintenanceCONNECTION-TO-GROUND and Disturbances Suppression DBF Breaker Failure Protection GEK-106168E Keyboard and Display DBF General ElectricMenu Tree SETINF ACTSettings Group SET KEY View Settings ProtectionModify Settings Protection View Protection SettingsConfirm Setting OUT Range Level Valid RangeInformation Group INF KEY StatusControl Group ACT KEY SET DATE/TIMESingle KEY Menu Configuration Menu DBF Breaker Failure Protection GEK-106168E Figures Breaker Failure Logic 189C4114 Sheet External Connections 189C4114 Sheet Front View 226B7412 H9 Rear View 226B7412H10 Dimensions Diagram 226B6086H10 Panel Drilling 226B6086H10 RS232 Connection DBF Relay to PC