GE 994-0089 Storage Recommendations, Environmental, Software, Storage Conditions, Battery Life

Page 18

GE Energy

Environmental

Operating temperature

-20 °C to +65 °C

 

Maximum ambient temperature is +50 °C for unit to fully

 

comply with IEC 61010-1 Section 10.1 regarding surface

 

temperature limits for protection against burns.

 

 

Humidity rating

5 % to 95 % relative humidity, non-condensing

 

 

Environmental rating

Ingress protection: IP30 (IEC 60529)

 

 

Installation / overvoltage

CAT III

category

 

 

 

Pollution degree

2

 

 

Use

Indoor use only

 

 

Altitude

Maximum altitude 10,000 ft [3000 m]

 

 

Software

Firmware

Embedded application dependent

 

 

Human machine interface

Built-in graphical user interface (Web browser-based)

 

 

Configuration

Built-in graphical user interface (Web browser-based)

 

Offline Configuration Manager (PC-based) - Future

 

 

Soft logic

IEC 61131-3 soft logic engine - Future

 

LogicLinx* Editor (if using LogicLinx)

 

 

1.5Storage Recommendations

Storage Conditions

Always store the D400 in an environment compatible with operating conditions. Recommended environmental conditions for storage are:

Temperature: -40 °C to +90 °C

Relative humidity: 5 % to 95 %, non-condensing

Exposure to excessive temperature or other extreme environmental conditions might cause damage and/or unreliable operation.

Battery Life

To maintain the life of the battery, you should remove the battery if the D400 will be powered down or stored for more than six months.

See section “7.2 Replacing the Battery”.

18994-0089–1.00–2, General

Image 18
Contents D400 Substation Data Manager Copyright Notice Trademark NoticesContents 994-0089-1.00-2, General Intended Audience About this DocumentPurpose Additional DocumentationHow to Use this Guide Document ConventionsContact Customer Support Product SupportSearch Technical Support Product ReturnsGE Energy Safety Precautions Before You StartSymbol Meaning CE Mark Compliance RoHS Material Declaration Data Content by AssemblyRegulatory Compliance Information Restriction of Hazardous Substances RoHSProduct Overview Features Hardware Overview14 994-0089-1.00-2, General Product Specifications SystemCommunications RS-232 Signal PropagationSerial communications RS-485Electrical PhysicalEnvironmental Battery LifeStorage Recommendations SoftwareInstalling the D400 Installation Steps» Follow these main steps to install and set up the D400 Required Tools Shipping Inspection Package ContentsUnpacking the D400 UnpackingFirst Look at the D400 Front PanelRear Panel » To mount the D400 on a rack Physical InstallationRack Mounting Panel Mount » To mount the D400 in a panelSetting up Communication Cards Communication CardsD400 I/O Adapter Card Slots Types of Communication Cards Network Slots 11Changing Card Settings » To change the settings on a communication cardConfiguration Options Factory DefaultRS-232 Adapter Switch SW1/SW2 Configuration RS-232 Adapter Top SideSwitch SW3/SW4 Configuration DTE default30 994-0089-1.00-2, General RS-485 Adapter RS-485 Adapter Top Side RS-485 Adapter Bottom Side Pull-up for TX+ Switch SW1 Configuration Fiber Optic Serial AdapterGE Energy IRIG-B Input Adapter Switch SW2 Configuration Switch SW3 ConfigurationIRIG-B Input Adapter IRIG-B Distribution Adapter IRIG-B Distribution Adapter4-Port Twisted-Pair Ethernet Switch Port Twisted-Pair Ethernet Switch CardHot Standby Fiber Optic Ethernet Switch Hot Standby Fiber Optic Ethernet Switch CardRedundant Twisted-Pair Ethernet + COM2 Port Adapter Redundant TP Ethernet + COM2 Port Adapter Card11 COM2 Port Adapter COM2 Port AdapterUSB KVM & Audio Adapter USB KVM AdapterConnecting to Devices and Networks Connection TypesTime Synchronization Local MaintenanceNetwork Local Substation ComputerGeneral Cabling Requirements Media Designation Cabling ConnectorCabling Overview D400 Field and Network ConnectionsHigh-Voltage Installations Number Function Signal Flow RS-232 ConnectionsRS-485 Connections Cabling RequirementsIN/OUT Wire Connections 52 994-0089-1.00-2, General Fiber Optic Connections Glass Optical FiberPlastic Optical Fiber See .5 Fiber Optic Serial Adapter for configuration options Fiber Optic Connector Signal Definitions Function IRIG-B ConnectionsIRIG-B Input Adapter IRIG-B Distribution Adapter Network Connections » To connect a local PC to the D400Ethernet Crossover Cable RJ-45 Pin Out D400 Switch/Hub Name D400 Name PinColor Modem Connections COM2 Port DB-9 Connector Signal Definitions Pin Signal DB-9 DB-25 Pin #COM2 Port DB-9 to DB-25 Pin out Local HMI Connection PC Pin # D400 Pin # Signal Front Maintenance PortD400 Front Serial Port DB-9 Pin Out Pin # Signal » To connect your computer to the D400Powering Up the D400 Power Supply OptionsRedundant Power Supply Power ConfigurationsPower Input Ranges Power Connections Wiring RequirementsExternal Power Requirements » To connect the power source to the D400If your power supply is… Then… Power Source Configurations Connection Wiring Diagram SUPPLY1 SUPPLY2 inputPower Source Connection Wiring Diagram » To connect the Power Fail contact closure Power Supply AlarmsPower Fail Alarm Wire the lamp between…Power Fail Alarm Connection System Fail» To connect the System Fail relay System Fail Alarm Connection D400 Front LEDs Front Panel LEDsSystem Status LEDs LED Display Status DescriptionSerial Port Status LEDs Configuring the D400 Connecting to the D400 for the First Time» To connect to the D400 Under Function, arrow … » To configure the network interface GE Energy Default IP address is Servicing the D400 Removing the D400 Main Module » To remove and re-insert the D400 main moduleD400 Main Module Replacing the Battery D400 Battery LocationBefore You Remove the Battery… Supported Battery TypesSupported battery replacements Manufacturer Mfg. Part Checking Voltage » To insert or replace the D400 batteryCleaning and Handling Lithium Batteries Disposing of Batteries» To change the System CompactFlash card User CompactFlash Access PanelChanging the CompactFlash » To change the User CompactFlash card» To replace a D400 power supply unit Replacing the Power SupplyBefore You Remove the Power Supply… D400 Power Supply UnitStandards & Protection GE Energy Category Standard Name DescriptionIeee Ordering Guide Product IdentificationD400 Ordering Guide Serial Communications SlotsVersion Rev Date Author Authentication RecordModification Record Change Description