GE 994-0089 user manual Servicing the D400

Page 79

GE Energy

7

Servicing the D400

The D400 does not require any scheduled maintenance. However, you may need to replace the following parts occasionally:

•System battery

•CompactFlash card

A periodic inspection is also suggested to ensure that:

•Unit has sustained no accidental physical damage

•Airflow is not obstructed

•Connectors and cables are intact and firmly attached

•Battery condition is good

Only trained personnel should perform maintenance on the D400.

D400 Substation Data Manager User's Manual 79

Image 79

Contents D400 Substation Data Manager Trademark Notices Copyright NoticeContents 994-0089-1.00-2, General Additional Documentation About this DocumentPurpose Intended AudienceDocument Conventions How to Use this GuideProduct Returns Product SupportSearch Technical Support Contact Customer SupportGE Energy Before You Start Safety PrecautionsSymbol Meaning Restriction of Hazardous Substances RoHS RoHS Material Declaration Data Content by AssemblyRegulatory Compliance Information CE Mark ComplianceProduct Overview Hardware Overview Features14 994-0089-1.00-2, General System Product SpecificationsCommunications RS-485 Signal PropagationSerial communications RS-232Physical ElectricalSoftware Battery LifeStorage Recommendations EnvironmentalInstallation Steps Installing the D400» Follow these main steps to install and set up the D400 Required Tools Unpacking Package ContentsUnpacking the D400 Shipping InspectionFront Panel First Look at the D400Rear Panel Panel Mount » To mount the D400 in a panel Physical InstallationRack Mounting » To mount the D400 on a rackCommunication Cards Setting up Communication CardsD400 I/O Adapter Card Slots Network Slots 11 Types of Communication Cards» To change the settings on a communication card Changing Card SettingsFactory Default Configuration OptionsRS-232 Adapter RS-232 Adapter Top Side Switch SW1/SW2 ConfigurationDTE default Switch SW3/SW4 Configuration30 994-0089-1.00-2, General RS-485 Adapter RS-485 Adapter Top Side RS-485 Adapter Bottom Side Pull-up for TX+ Fiber Optic Serial Adapter Switch SW1 ConfigurationGE Energy IRIG-B Input Adapter Switch SW3 Configuration Switch SW2 ConfigurationIRIG-B Input Adapter IRIG-B Distribution Adapter IRIG-B Distribution AdapterPort Twisted-Pair Ethernet Switch Card 4-Port Twisted-Pair Ethernet SwitchHot Standby Fiber Optic Ethernet Switch Card Hot Standby Fiber Optic Ethernet SwitchRedundant TP Ethernet + COM2 Port Adapter Card Redundant Twisted-Pair Ethernet + COM2 Port AdapterCOM2 Port Adapter 11 COM2 Port AdapterUSB KVM Adapter USB KVM & Audio AdapterConnection Types Connecting to Devices and NetworksLocal Substation Computer Local MaintenanceNetwork Time SynchronizationD400 Field and Network Connections Media Designation Cabling ConnectorCabling Overview General Cabling RequirementsHigh-Voltage Installations RS-232 Connections Number Function Signal FlowCabling Requirements RS-485 ConnectionsIN/OUT Wire Connections 52 994-0089-1.00-2, General Glass Optical Fiber Fiber Optic ConnectionsPlastic Optical Fiber See .5 Fiber Optic Serial Adapter for configuration options IRIG-B Connections Fiber Optic Connector Signal Definitions FunctionIRIG-B Input Adapter IRIG-B Distribution Adapter » To connect a local PC to the D400 Network ConnectionsD400 Name Pin Ethernet Crossover Cable RJ-45 Pin Out D400 Switch/Hub NameColor Modem Connections Signal DB-9 DB-25 Pin # COM2 Port DB-9 Connector Signal Definitions PinCOM2 Port DB-9 to DB-25 Pin out Local HMI Connection » To connect your computer to the D400 Front Maintenance PortD400 Front Serial Port DB-9 Pin Out Pin # Signal PC Pin # D400 Pin # SignalPower Supply Options Powering Up the D400Power Configurations Redundant Power SupplyPower Input Ranges Wiring Requirements Power Connections» To connect the power source to the D400 External Power RequirementsIf your power supply is… Then… SUPPLY1 SUPPLY2 input Power Source Configurations Connection Wiring DiagramPower Source Connection Wiring Diagram Wire the lamp between… Power Supply AlarmsPower Fail Alarm » To connect the Power Fail contact closureSystem Fail Power Fail Alarm Connection» To connect the System Fail relay System Fail Alarm Connection LED Display Status Description Front Panel LEDsSystem Status LEDs D400 Front LEDsSerial Port Status LEDs Connecting to the D400 for the First Time Configuring the D400» To connect to the D400 Under Function, arrow … » To configure the network interface GE Energy Default IP address is Servicing the D400 » To remove and re-insert the D400 main module Removing the D400 Main ModuleD400 Main Module D400 Battery Location Replacing the BatterySupported Battery Types Before You Remove the Battery…Supported battery replacements Manufacturer Mfg. Part Disposing of Batteries » To insert or replace the D400 batteryCleaning and Handling Lithium Batteries Checking Voltage» To change the User CompactFlash card User CompactFlash Access PanelChanging the CompactFlash » To change the System CompactFlash cardD400 Power Supply Unit Replacing the Power SupplyBefore You Remove the Power Supply… » To replace a D400 power supply unitStandards & Protection Category Standard Name Description GE EnergyIeee Product Identification Ordering GuideSerial Communications Slots D400 Ordering GuideChange Description Authentication RecordModification Record Version Rev Date Author