Configuration and Operation
+5V IN | OFF |
|
|
|
|
|
| P4 |
|
|
|
| P3 | P2 |
| P1 |
|
|
|
| |
P8 | ON |
|
|
| U16 | IrDA |
| |||
| EXT UART DCE | UART4 DTE | UART1 DCE |
| USB OTG |
|
| |||
|
|
|
|
| ||||||
| SW1 | P9 | DTR | DSR | CD | RI |
|
|
|
|
|
|
|
|
|
| |||||
|
| ETHERNET | ACT | NC | NC | NC | 3 | VR1 |
|
|
| F1 |
|
|
|
|
| 2 |
| CON | |
| 2A |
| SD2_D0 | SD2_D1 | SD2_D2 | SD2_D3 | 1 | BATT EM | ||
|
| J3 | J4 | J5 | J6 |
| ||||
|
|
|
| LCD | ||||||
|
|
|
|
|
| |||||
BASE BOARD |
| CPU BOARD |
|
|
|
|
| |||
|
|
|
|
|
|
| ||||
|
|
|
|
|
| PX1/PY1 |
|
|
|
|
|
| LED6 | LED5 |
|
|
|
|
|
SW2 |
|
|
|
|
|
|
|
|
RESET | LINK | ACT | P20 |
|
| ENCODERTV CON | ||
VCC PWR | LED2 |
|
| |||||
3 | BOOT2 |
|
| |||||
|
| S2 |
|
|
|
| PK1 |
|
5V PWR | LED1 | 1 | BOOT0 |
|
|
|
|
|
2 | BOOT1 |
|
|
|
|
| ||
STAT2 | LED3 | 4 | BOOT3 |
|
|
| U6 | U7 |
STAT1 | LED4 | 5 | CLKMODE0 |
|
|
|
|
|
6 | CLKMODE1 |
| U5 |
|
|
| ||
BUS ACT | LED7 | 7 | SW1 IRQ | CARD |
|
|
| |
|
| 8 | SW2 READ | PM1 |
| U8 | U9 | |
|
|
|
| |||||
|
|
|
|
| ||||
BUZZER |
| S1 |
| NANDFLASH |
| CPU |
|
|
LINE IN |
|
| PK2 | KEYPADCON | ||||
6 | TONE_OUT |
|
| |||||
|
| 1 | UART1_ON |
|
|
|
|
|
|
| 2 | UART4_ON |
|
|
|
|
|
|
| 3 | IrDA_ON |
| PM2 |
|
|
|
|
| 4 | NEXUS_EN |
|
|
|
| |
P10 |
|
| J1 | J3 | J2 |
| ||
| 5 | JTAG_CTRL |
|
| ||||
|
|
|
|
|
|
| ||
|
| 7 | PEN_CS_B |
|
|
|
|
|
P11 |
| 8 | PEN_IRQ_B |
|
|
| PX2/PY2 |
|
|
|
|
|
|
|
|
| |
MIC IN |
|
|
|
|
|
|
| |
|
|
|
| P12 |
|
| J7 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
| HEADPHONE |
|
| ONE WIRE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SD/MMC |
| |||||||||||||||
|
|
|
| PE3 |
|
|
|
|
|
|
|
|
|
| PE2 |
|
|
|
|
|
|
|
|
| PE1 |
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| EXP CON 2 |
|
|
|
|
|
|
|
| EXP CON 1 |
|
|
|
|
|
|
| CSI |
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P7
P13
P5
P6
P1
P2
| J2 |
CARD | VGA |
ENCODERTV | |
| J1 |
| CVBS |
| J3 |
Figure 2-12. Installation of the TV Encoder Card
2.5.1Using the TFT LCD Display Panel
The ADS is equipped with a Sharp LQ035Q7DB02 touch control enabled TFT LCD display assembly. The ADS documentation CD contains specifications for the TFT LCD component.
CAUTION
Make sure that the input power to the main board is disconnected or switched off before connecting the LCD module. Connecting the module with power applied can damage the LCD module and/or the main board.
To use the TFT LCD display, connect the 34 conductor ribbon cable supplied with the ADS from J11 on the LCD module to P7 on the Base board.
The potentiometer VR1, which is to the left of the LCD panel just below J11, controls flickering of the display screen. This control is set at the factory and normally does not require adjustment. However, if the TFT LCD display flickers, you may adjust VR1 to stabilize the display. Use a suitable flat head or phillips head screwdriver. Because the adjustment is normally done with power applied, we recommend use of a plastic blade tool.
| M9328MX21ADSE User’s Manual, Rev. A |
Freescale Semiconductor |