Enterasys Networks manual Matrix X16-C Chassis Setup, Required Tools

Page 33

3

Matrix X16-C Chassis Setup

This chapter describes the following:

For information about:	Refer to page ...

Required Tools	3-1

Unpacking the Matrix X16-C Chassis	3-2

Setting Up the Matrix X16-C Chassis	3-5

Installing and Removing a Power Supply	3-13

Installing and Removing a Fan Tray	3-18

Installing and Removing Modules	3-20

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit	3-26

Installing the Optional Cable Management Kit	3-38

Powering Up the Matrix X16-C Chassis	3-41

LEDs and Reset Button	3-42

First-Time Quick Configuration	3-47

Required Tools

Installation equipment needed includes:

• Box cutter

• Phillips screwdriver

• Flat blade screwdriver

Electrical Hazard: Only qualified personnel should install or service this unit.

Riesgo Eléctrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

A box cutter is required to cut the shipping straps. A Phillips screwdriver is needed to install the unit in a 19‐inch (48.26‐centimeter) equipment rack and to install the optional Cable Management Kit (refer to “Optional Cable Management Kit” on page 3‐37 for more information). A flat blade screwdriver is used to tighten and loosen captive screws. Refer to Chapter 2 for guidelines that must be followed to install the Matrix X16‐C chassis.

Matrix X16-C Chassis Installation Guide 3-1

Image 33

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Using This Guide Who Should Use This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View Features X16-C Input/Output ModulesX16-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X16-C Fabric ModulePower Supply LEDs X16-C Redundant Power SuppliesAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Features Overview Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X16-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X16-C ChassisShipping bag Shipping skid Chassis Accessory packageDisassembly Steps 6 through Setting Up the Matrix X16-C Chassis Setup OrderInstalling the Matrix X16-C Chassis Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screws Installing Optional Mid-Mount BracketsFastening Mid-Mount Brackets To rack‐mount the Matrix X16‐C chassis, proceed as follows Rack Mounting the Matrix X16-C ChassisRack Mounting the Matrix X16-C Chassis Rack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable Installing and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply PlanningPower supply slot PS1 Power supply coverplate Vent plate 13 Removing Power Supply Vent Plate15 Removing Blank Coverplate from Power Supply Slot 14 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling a Fan Tray Installing and Removing a Fan Tray17 Removing Bottom Bezel Installing and Removing Modules Installing and Removing IOMsRemoving a Fan Tray Captive screws IOM guide rails Ejector handles IOM slot21 Removing IOM Coverplate 20 Engaging Ejector HandlesControl Module slot Guide rails Captive screws Installing and Removing CMsReplacing the CM Battery 23 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiver Removing an XFP/SFP Module25 Attaching LC or MT-RJ Cable Connector Connecting Fiber-Optic CablesParameter Setting Connecting to the CM COM Port26 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal27 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsConnecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit To install the Cable Management Kit, proceed as follows Installing the Optional Cable Management Kit33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps 35 Connecting 20 Amp AC Power Cord to the Power Supply Powering Up the Matrix X16-C ChassisPower Supply LEDs LEDs and Reset ButtonDC/AC Power Supply PS1-PS6 LED Definitions Function LED Activity DC Power LED37 Fan Tray LED Fan Tray LEDsControl and Fabric Module LEDs Module LEDs and Reset ButtonFan Tray LED Definitions Function LED ActivityControl and Fabric Module LED Definitions State LED ActivityCM LEDs Only State LED Activity IOM LED Definitions IOM LEDsStatus LED LED Activity Ethernet Port LED RX/TX LED ActivityFirst-Time Quick Configuration Configuring DhcpAssigning an IP Address to eth0 Naming the Matrix X16-C Enabling NTPTable A-1 Matrix X-16C Specifications Chassis, Power Supply, and Fan Tray SpecificationsSpecification AC Power Supply ModuleTable A-2 AC Power Supply Requirements Fan TrayEnvironmental Table A-3 Module Power Specifications Table A-4 Redundancy Configurations for AC Line 100-120 VacTable A-5 Redundancy Configurations for AC Line 200-240 Vac Table A-6 Twist Lock Power Cord Options Gigabit Ethernet Transceiver Specifications XFPTable A-8 XFP Fiber-Optic Specifications Module Wavelength Tx Power Rx Sensitivity Link PowerGigabit Ethernet Transceiver Specifications SFP Table A-9 Recommended Cable Types and SpecificationsType Max. Reach Min. Reach1 Connector MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX SFP Input/Output SpecificationsTable A-10 Mini-GBIC Input/Output Port Specifications Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXMGBIC-02 Specifications 1000BASE-T MGBIC-08 Specifications 1000BASE-ELXTable A-17 MGBIC-08 Optical Specifications Table A-19 MGBIC-02 SpecificationsCOM Port Pinout Assignments Pin Signal Name Input/OutputRegulatory Compliance Table A-20 COM Port Pin AssignmentsPage Index Mtbf RX/TX LED Index-4