Enterasys Networks X16-C Installing a Compact Flash Card, USB device Control Module USB port

Page 66

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

Figure 3-29 Attaching a USB Device to the CM

2

1

STATUS

ACTIVE/

STANDBY

RESET

USB

3

1 USB device

2 Control Module

3 USB port

Installing a Compact Flash Card

The Control Module provides an IDE port housing a 1 GB Flash memory card, as shown in Figure 3‐30. If the factory‐installed card fails or you want to install a new Type I Compact Flash card, simply pull the old card from its connector and insert the new card.

Figure 3-30 Installing Flash Card

STATUS

ACTIVE/

STANDBY

RESET

USB

ETHERNET

COM

2

31

1 Compact Flash card

2 Connector

3 Control Module

3-34 Matrix X16-C Chassis Setup

Image 66

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables Using This Guide Who Should Use This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View Features X16-C Input/Output ModulesX16-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X16-C Fabric Module Monitor ValuesAuto-Ranging Power Supplies X16-C Redundant Power SuppliesPower Supply LEDs Power Supply ReplacementRack-Mountable Chassis Features Overview Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X16-C Chassis Setup Required ToolsUnpacking the Matrix X16-C Chassis Shipping straps Shipping box Shipping skidAccessory package Shipping bag Shipping skid ChassisDisassembly Steps 6 through Setting Up the Matrix X16-C Chassis Setup OrderInstalling the Matrix X16-C Chassis Installing Optional Rack Support Brackets Installing Optional Mid-Mount Brackets Rack Rack support brackets Bracket screwsFastening Mid-Mount Brackets Rack Mounting the Matrix X16-C Chassis To rack‐mount the Matrix X16‐C chassis, proceed as followsRack Mounting the Matrix X16-C Chassis Chassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisTelcordia GR-1089 Grounding Hole Pattern and Cable Installing and Removing a Power Supply Attaching the Electrostatic Discharge Wrist StrapGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply13 Removing Power Supply Vent Plate Power supply slot PS1 Power supply coverplate Vent plate14 Installing Power Supply Module 15 Removing Blank Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing and Removing a Fan Tray Installing a Fan Tray17 Removing Bottom Bezel Installing and Removing Modules Installing and Removing IOMsRemoving a Fan Tray IOM slot Captive screws IOM guide rails Ejector handles20 Engaging Ejector Handles 21 Removing IOM CoverplateInstalling and Removing CMs Control Module slot Guide rails Captive screwsReplacing the CM Battery Installing and Removing FMs 23 Installing Fabric ModuleInstalling an XFP/SFP Module Removing an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiverConnecting Fiber-Optic Cables 25 Attaching LC or MT-RJ Cable ConnectorConnecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 26 Connecting an IBM PC or Compatible Connecting the CM COM Port to a Modem 27 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal DiagramConnecting to the CM USB Port VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Installing a Compact Flash Card Compact Flash card Connector Control ModuleUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsOptional Cable Management Kit Installing the Optional Cable Management Kit To install the Cable Management Kit, proceed as follows33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps Powering Up the Matrix X16-C Chassis 35 Connecting 20 Amp AC Power Cord to the Power SupplyDC/AC Power Supply PS1-PS6 LED Definitions LEDs and Reset ButtonPower Supply LEDs Function LED Activity DC Power LEDFan Tray LEDs 37 Fan Tray LEDFan Tray LED Definitions Module LEDs and Reset ButtonControl and Fabric Module LEDs Function LED ActivityControl and Fabric Module LED Definitions State LED ActivityCM LEDs Only State LED Activity Status LED LED Activity IOM LEDsIOM LED Definitions Ethernet Port LED RX/TX LED ActivityFirst-Time Quick Configuration Configuring DhcpAssigning an IP Address to eth0 Enabling NTP Naming the Matrix X16-CSpecification Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X-16C Specifications AC Power Supply ModuleTable A-2 AC Power Supply Requirements Fan TrayEnvironmental Table A-3 Module Power Specifications Table A-4 Redundancy Configurations for AC Line 100-120 VacTable A-5 Redundancy Configurations for AC Line 200-240 Vac Table A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications XFPTable A-6 Twist Lock Power Cord Options Module Wavelength Tx Power Rx Sensitivity Link PowerGigabit Ethernet Transceiver Specifications SFP Table A-9 Recommended Cable Types and SpecificationsType Max. Reach Min. Reach1 Connector Table A-10 Mini-GBIC Input/Output Port Specifications SFP Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-17 MGBIC-08 Optical Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-19 MGBIC-02 SpecificationsRegulatory Compliance Pin Signal Name Input/OutputCOM Port Pinout Assignments Table A-20 COM Port Pin AssignmentsPage Index Mtbf RX/TX LED Index-4