Enterasys Networks X16-C manual Table A-3 Module Power Specifications

Page 83

Power Supply Requirements, Specifications, and Twist Lock Options

Table A-3 Module Power Specifications

	@ 110 Vac / 220 Vac

Module	Power (Watts)	Thermal Output (BTU/HR)

CM	97 Watts	331.1 BTU/HR

Fan tray	85 Watts	290.1 BTU/HR

X4-FM	30 Watts	102.4 BTU/HR

X8-FM	62 Watts	211.6 BTU/HR

X16-FM	98 Watts	334.5 BTU/HR

X-G32-00	155 Watts	520.0 BTU/HR

X-GT16-00	105 Watts	358.3 BTU/HR

X-M2-00	155 Watts	520.0 BTU/HR

X-T32-00	155 Watts	520.0 BTU/HR

Table A-4 Redundancy Configurations for AC Line 100–120 Vac

No. of Power Supplies	Maximum Redundant System Load1	Redundancy Configuration
2	1160 Watts	1 + 1

3	2320 Watts	N + 1

4	3480 Watts	1 + 1

4	3480 Watts	N + 1

5	4640 Watts	N + 1

6	5800 Watts	1 + 1

6	5800 Watts	N + 1

1. The sum of individual power draws for all installed fan trays, control and fabric modules, and IOMs.

Table A-5 Redundancy Configurations for AC Line 200–240 Vac

No. of Power Supplies	Maximum Redundant System Load1	Redundancy Configuration
2	1500 Watts	1 + 1

3	3000 Watts	N + 1

4	3000 Watts	1 + 1

4	4500 Watts	N + 1

5	6000 Watts	N + 1

6	4500 Watts	1 + 1

6	6000 Watts	N + 1

1. The sum of individual power draws for all installed fan trays, control and fabric modules, and IOMs.

Matrix X16-C Chassis Installation Guide A-3

Image 83

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables For information about Refer to Using This GuideWho Should Use This Guide Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View X16-C Control Module FeaturesX16-C Input/Output Modules Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X16-C Fabric ModulePower Supply Replacement X16-C Redundant Power SuppliesPower Supply LEDs Auto-Ranging Power SuppliesRack-Mountable Chassis Features Overview Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X16-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X16-C ChassisShipping bag Shipping skid Chassis Accessory packageDisassembly Steps 6 through Installing the Matrix X16-C Chassis Setting Up the Matrix X16-C ChassisSetup Order Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screws Installing Optional Mid-Mount BracketsFastening Mid-Mount Brackets To rack‐mount the Matrix X16‐C chassis, proceed as follows Rack Mounting the Matrix X16-C ChassisRack Mounting the Matrix X16-C Chassis Rack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable Grounding Receptacle Plug Wrist strap Installing and Removing a Power SupplyAttaching the Electrostatic Discharge Wrist Strap Installing a Power Supply Power Supply PlanningPower supply slot PS1 Power supply coverplate Vent plate 13 Removing Power Supply Vent Plate15 Removing Blank Coverplate from Power Supply Slot 14 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling a Fan Tray Installing and Removing a Fan Tray17 Removing Bottom Bezel Removing a Fan Tray Installing and Removing ModulesInstalling and Removing IOMs Captive screws IOM guide rails Ejector handles IOM slot21 Removing IOM Coverplate 20 Engaging Ejector HandlesControl Module slot Guide rails Captive screws Installing and Removing CMsReplacing the CM Battery 23 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiver Removing an XFP/SFP Module25 Attaching LC or MT-RJ Cable Connector Connecting Fiber-Optic CablesParameter Setting Connecting to the CM COM Port26 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal27 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 USB device Control Module USB port Installing a Compact Flash CardCompact Flash card Connector Control Module Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit To install the Cable Management Kit, proceed as follows Installing the Optional Cable Management Kit33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps 35 Connecting 20 Amp AC Power Cord to the Power Supply Powering Up the Matrix X16-C ChassisFunction LED Activity DC Power LED LEDs and Reset ButtonPower Supply LEDs DC/AC Power Supply PS1-PS6 LED Definitions37 Fan Tray LED Fan Tray LEDsFunction LED Activity Module LEDs and Reset ButtonControl and Fabric Module LEDs Fan Tray LED DefinitionsCM LEDs Only State LED Activity Control and Fabric Module LED DefinitionsState LED Activity Ethernet Port LED RX/TX LED Activity IOM LEDsIOM LED Definitions Status LED LED ActivityAssigning an IP Address to eth0 First-Time Quick ConfigurationConfiguring Dhcp Naming the Matrix X16-C Enabling NTPAC Power Supply Module Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X-16C Specifications SpecificationEnvironmental Table A-2 AC Power Supply RequirementsFan Tray Table A-5 Redundancy Configurations for AC Line 200-240 Vac Table A-3 Module Power SpecificationsTable A-4 Redundancy Configurations for AC Line 100-120 Vac Module Wavelength Tx Power Rx Sensitivity Link Power Gigabit Ethernet Transceiver Specifications XFPTable A-6 Twist Lock Power Cord Options Table A-8 XFP Fiber-Optic SpecificationsType Max. Reach Min. Reach1 Connector Gigabit Ethernet Transceiver Specifications SFPTable A-9 Recommended Cable Types and Specifications Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical Specifications SFP Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-10 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-19 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-17 MGBIC-08 Optical SpecificationsTable A-20 COM Port Pin Assignments Pin Signal Name Input/OutputCOM Port Pinout Assignments Regulatory CompliancePage Index Mtbf RX/TX LED Index-4