Enterasys Networks X16-C manual Installing an XFP/SFP Module

Page 58

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

4.After completing all module installation, be sure that you leave no slots uncovered. Failure to seal any empty slots with the provided coverplates may hamper power cooling of the chassis and its components.

5.To remove an installed FM, first disconnect any cabling and perform the installation steps in reverse.

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

Matrix X Router modules provide the following interfaces for cable and Flash card connections:

•IOM: XFP or SFP optical ports

•CM: Two serial RJ45 ports for Ethernet and Console (COM) connections

•CM: USB port

•CM: IDE port for connection to Type I Compact Flash card

Matrix X Router IOMs support XFP (10‐Gigabit Small Form‐Factor Pluggable) and SFP (Small Form‐Factor Pluggable) hot‐swappable optical transceivers for 10‐ and 1‐Gigabit and 10/100/1000 Ethernet connections.

Installing an XFP/SFP Module

This section describes how to install an XFP or SFP optical transceiver. For XFP/SFP specifications, refer to Appendix A, Specifications and Regulatory Compliance.

Caution: Carefully follow the instructions in this manual to avoid damaging the XFP/SPF and IOM module.

The XFP/SPF and IOM module are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to the XFP/SPF and IOM module. Always leave the XFP/SPF and IOM module in the antistatic bag or an equivalent antistatic container when not installed.

Precaución: Siga las instrucciones del manual para no dañar el XFP/SPF o la módulo IOM, puesto que son muy sensible a las descargas de electricidad estática. Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no lo hace, podría dañar el XFP/SPF y la módulo IOM. Mientras no esté instalado, mantenga el XFP/SPF y la módulo IOM en su bolsa antiestática o en cualquier otro recipiente antiestático.

Warning: Fiber-optic XFP/SFPs use Class 1 lasers. Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter. Advertencia: Los XFP/SFPs de fibra optica usan lasers de clase 1. No se debe usar instrumentos opticos para ver la potencia laser. El uso de los instrumentos opticos para ver la potencia laser incrementa el riesgo a los ojos. Cuando vean el puerto de la potencia optica, la corriente debe ser removida del adaptador de la red.

Warnhinweis: XFP/SFPs mit Fiber-Optik Technologie benutzen Laser der Klasse 1. Benutzen sie keinesfalls optische Hilfsmittel, um die Funktion des Lasers zu überprüfen. Solche Hilfsmittel erhöhen die Gefahr von Sehschäden. Wenn sie den optischen Port überprüfen möchten stellen Sie sicher, dass die Komponente von der Spannungsversorgung getrennt ist.

3-26 Matrix X16-C Chassis Setup

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View X16-C Input/Output Modules FeaturesX16-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X16-C Fabric Module Monitor ValuesAuto-Ranging Power Supplies X16-C Redundant Power SuppliesPower Supply LEDs Power Supply ReplacementRack-Mountable Chassis Features Overview Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X16-C Chassis Setup Required ToolsUnpacking the Matrix X16-C Chassis Shipping straps Shipping box Shipping skidAccessory package Shipping bag Shipping skid ChassisDisassembly Steps 6 through Setup Order Setting Up the Matrix X16-C ChassisInstalling the Matrix X16-C Chassis Installing Optional Rack Support Brackets Installing Optional Mid-Mount Brackets Rack Rack support brackets Bracket screwsFastening Mid-Mount Brackets Rack Mounting the Matrix X16-C Chassis To rack‐mount the Matrix X16‐C chassis, proceed as followsRack Mounting the Matrix X16-C Chassis Chassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisTelcordia GR-1089 Grounding Hole Pattern and Cable Attaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply13 Removing Power Supply Vent Plate Power supply slot PS1 Power supply coverplate Vent plate14 Installing Power Supply Module 15 Removing Blank Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing and Removing a Fan Tray Installing a Fan Tray17 Removing Bottom Bezel Installing and Removing IOMs Installing and Removing ModulesRemoving a Fan Tray IOM slot Captive screws IOM guide rails Ejector handles20 Engaging Ejector Handles 21 Removing IOM CoverplateInstalling and Removing CMs Control Module slot Guide rails Captive screwsReplacing the CM Battery Installing and Removing FMs 23 Installing Fabric ModuleInstalling an XFP/SFP Module Removing an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiverConnecting Fiber-Optic Cables 25 Attaching LC or MT-RJ Cable ConnectorConnecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 26 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 27 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal DiagramVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsOptional Cable Management Kit Installing the Optional Cable Management Kit To install the Cable Management Kit, proceed as follows33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps Powering Up the Matrix X16-C Chassis 35 Connecting 20 Amp AC Power Cord to the Power SupplyDC/AC Power Supply PS1-PS6 LED Definitions LEDs and Reset ButtonPower Supply LEDs Function LED Activity DC Power LEDFan Tray LEDs 37 Fan Tray LEDFan Tray LED Definitions Module LEDs and Reset ButtonControl and Fabric Module LEDs Function LED ActivityState LED Activity Control and Fabric Module LED DefinitionsCM LEDs Only State LED Activity Status LED LED Activity IOM LEDsIOM LED Definitions Ethernet Port LED RX/TX LED ActivityConfiguring Dhcp First-Time Quick ConfigurationAssigning an IP Address to eth0 Enabling NTP Naming the Matrix X16-CSpecification Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X-16C Specifications AC Power Supply ModuleFan Tray Table A-2 AC Power Supply RequirementsEnvironmental Table A-4 Redundancy Configurations for AC Line 100-120 Vac Table A-3 Module Power SpecificationsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Table A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications XFPTable A-6 Twist Lock Power Cord Options Module Wavelength Tx Power Rx Sensitivity Link PowerTable A-9 Recommended Cable Types and Specifications Gigabit Ethernet Transceiver Specifications SFPType Max. Reach Min. Reach1 Connector Table A-10 Mini-GBIC Input/Output Port Specifications SFP Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-17 MGBIC-08 Optical Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-19 MGBIC-02 SpecificationsRegulatory Compliance Pin Signal Name Input/OutputCOM Port Pinout Assignments Table A-20 COM Port Pin AssignmentsPage Index Mtbf RX/TX LED Index-4
Top Page Image Contents