Enterasys Networks X16-C manual Fastening Mid-Mount Brackets

Page 40

Setting Up the Matrix X16-C Chassis

Figure 3-6 Fastening Mid-Mount Brackets

2

1

	FAN TRAY		FAN TRAY		FAN TRAY
	FAN TRAY
9	10	11	12	13	14	15	16
			FM1	FM2
			CM1	CM2
			GROUND
			S/N:	MAC ADD.
				STRAP
1	2	3	4	5	6	7	8

FAN TRAY	FAN TRAY	FAN TRAY
1	2	3

2

1

1 Mid-mount brackets (2)

2 Bracket screws (30)

3-8 Matrix X16-C Chassis Setup

Image 40

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View X16-C Input/Output Modules FeaturesX16-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 X16-C Fabric Module Monitor ValuesX16-C Redundant Power Supplies Power Supply LEDsAuto-Ranging Power Supplies Power Supply ReplacementRack-Mountable Chassis Features Overview Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X16-C Chassis Setup Required ToolsUnpacking the Matrix X16-C Chassis Shipping straps Shipping box Shipping skidAccessory package Shipping bag Shipping skid ChassisDisassembly Steps 6 through Setup Order Setting Up the Matrix X16-C ChassisInstalling the Matrix X16-C Chassis Installing Optional Rack Support Brackets Installing Optional Mid-Mount Brackets Rack Rack support brackets Bracket screwsFastening Mid-Mount Brackets Rack Mounting the Matrix X16-C Chassis To rack‐mount the Matrix X16‐C chassis, proceed as followsRack Mounting the Matrix X16-C Chassis Chassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisTelcordia GR-1089 Grounding Hole Pattern and Cable Attaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Power Supply Planning Installing a Power Supply13 Removing Power Supply Vent Plate Power supply slot PS1 Power supply coverplate Vent plate14 Installing Power Supply Module 15 Removing Blank Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing and Removing a Fan Tray Installing a Fan Tray17 Removing Bottom Bezel Installing and Removing IOMs Installing and Removing ModulesRemoving a Fan Tray IOM slot Captive screws IOM guide rails Ejector handles20 Engaging Ejector Handles 21 Removing IOM CoverplateInstalling and Removing CMs Control Module slot Guide rails Captive screwsReplacing the CM Battery Installing and Removing FMs 23 Installing Fabric ModuleInstalling an XFP/SFP Module Removing an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiverConnecting Fiber-Optic Cables 25 Attaching LC or MT-RJ Cable ConnectorConnecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 26 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 27 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal DiagramVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsOptional Cable Management Kit Installing the Optional Cable Management Kit To install the Cable Management Kit, proceed as follows33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps Powering Up the Matrix X16-C Chassis 35 Connecting 20 Amp AC Power Cord to the Power SupplyLEDs and Reset Button Power Supply LEDsDC/AC Power Supply PS1-PS6 LED Definitions Function LED Activity DC Power LEDFan Tray LEDs 37 Fan Tray LEDModule LEDs and Reset Button Control and Fabric Module LEDsFan Tray LED Definitions Function LED ActivityState LED Activity Control and Fabric Module LED DefinitionsCM LEDs Only State LED Activity IOM LEDs IOM LED DefinitionsStatus LED LED Activity Ethernet Port LED RX/TX LED ActivityConfiguring Dhcp First-Time Quick ConfigurationAssigning an IP Address to eth0 Enabling NTP Naming the Matrix X16-CChassis, Power Supply, and Fan Tray Specifications Table A-1 Matrix X-16C SpecificationsSpecification AC Power Supply ModuleFan Tray Table A-2 AC Power Supply RequirementsEnvironmental Table A-4 Redundancy Configurations for AC Line 100-120 Vac Table A-3 Module Power SpecificationsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Gigabit Ethernet Transceiver Specifications XFP Table A-6 Twist Lock Power Cord OptionsTable A-8 XFP Fiber-Optic Specifications Module Wavelength Tx Power Rx Sensitivity Link PowerTable A-9 Recommended Cable Types and Specifications Gigabit Ethernet Transceiver Specifications SFPType Max. Reach Min. Reach1 Connector SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXTable A-10 Mini-GBIC Input/Output Port Specifications Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-17 MGBIC-08 Optical Specifications Table A-19 MGBIC-02 SpecificationsPin Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-20 COM Port Pin AssignmentsPage Index Mtbf RX/TX LED Index-4