Enterasys Networks X16-C manual Installing and Removing CMs

Page 55

Installing and Removing Modules

Installing and Removing CMs

Note: If you ordered the Memory Upgrade Kit (X-4G-MEM), install the DIMMs first. For installation instructions, refer to “Installing the Memory Upgrade Kit” on page 3-35.

1.Locate the empty CM1 slot, and position the module in the guide rail at the left of the slot, as shown in Figure 3‐22. Gently insert the module until it engages with the backplane connectors. Be sure the ejector handles are open as shown in Figure 3‐20.

2.Push the ejector handles toward the center of the module, as shown in Figure 3‐20, engaging the lip of the slot, until the module locks into place and is flush with adjoining coverplates.

3.Tighten the two captive screws.

4.After completing all module installation, be sure that you leave no slots uncovered. Failure to seal any empty slots with the provided coverplates may hamper power cooling of the chassis and its components.

5.To remove an installed CM, first disconnect any cabling and perform the installation steps in reverse.

Figure 3-22 Installing Control Module

3

1

4

5

TX

TX

RX

RX

TX

RX

TX RX

CM1

GROUND

STATUS

ACTIVE/

STANDBY

RESET

USB

ETHERNET

COM

2

S/N:

MAC ADD.

 

STRAP

1

2

3

4

5

5

6

 

FAN TRAY

 

FAN TRAY

 

 

TRAY

12

78

 

 

 

3

4

5

1

Control Module slot 1

3

Guide rails

 

5 Captive screws (2)

2

Control Module

4

Ejector handles (2)

 

Matrix X16-C Chassis Installation Guide 3-23

Image 55
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Index Appendix a Specifications and Regulatory ComplianceFigures Tables Who Should Use This Guide Using This GuideFor information about Refer to Conventions Used in This Guide Using the Matrix X Router Manual SetGetting Help Commonly Used AcronymsGetting Help Xviii About This Guide System Description OverviewMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View X16-C Input/Output Modules FeaturesX16-C Control Module Installing Redundant CMs into an Active Matrix X Router CM1 Monitor Values X16-C Fabric ModulePower Supply Replacement X16-C Redundant Power SuppliesPower Supply LEDs Auto-Ranging Power SuppliesRack-Mountable Chassis Features Overview Site Guidelines Site and Configuration GuidelinesConfiguration Guidelines Required Tools Matrix X16-C Chassis SetupShipping straps Shipping box Shipping skid Unpacking the Matrix X16-C ChassisShipping bag Shipping skid Chassis Accessory packageDisassembly Steps 6 through Setup Order Setting Up the Matrix X16-C ChassisInstalling the Matrix X16-C Chassis Installing Optional Rack Support Brackets Rack Rack support brackets Bracket screws Installing Optional Mid-Mount BracketsFastening Mid-Mount Brackets To rack‐mount the Matrix X16‐C chassis, proceed as follows Rack Mounting the Matrix X16-C ChassisRack Mounting the Matrix X16-C Chassis Rack Mounting the Mid-Mounted Chassis Chassis Bonding and GroundingTelcordia GR-1089 Grounding Hole Pattern and Cable Attaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power SupplyGrounding Receptacle Plug Wrist strap Installing a Power Supply Power Supply PlanningPower supply slot PS1 Power supply coverplate Vent plate 13 Removing Power Supply Vent Plate15 Removing Blank Coverplate from Power Supply Slot 14 Installing Power Supply ModuleInlet power cord AC inlet AC1 Removing a Power SupplyInstalling a Fan Tray Installing and Removing a Fan Tray17 Removing Bottom Bezel Installing and Removing IOMs Installing and Removing ModulesRemoving a Fan Tray Captive screws IOM guide rails Ejector handles IOM slot21 Removing IOM Coverplate 20 Engaging Ejector HandlesControl Module slot Guide rails Captive screws Installing and Removing CMsReplacing the CM Battery 23 Installing Fabric Module Installing and Removing FMsInstalling an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiver Removing an XFP/SFP Module25 Attaching LC or MT-RJ Cable Connector Connecting Fiber-Optic CablesParameter Setting Connecting to the CM COM Port26 Connecting an IBM PC or Compatible Connecting the CM COM Port to a VT Series Terminal27 Connecting a VT Series Terminal Connecting the CM COM Port to a ModemCOM Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Compact Flash card Connector Control Module Installing a Compact Flash CardUSB device Control Module USB port Removing the DIMMs Installing the Memory Upgrade KitConnector fingers Connector arms Installing the DIMMsOptional Cable Management Kit To install the Cable Management Kit, proceed as follows Installing the Optional Cable Management Kit33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps 35 Connecting 20 Amp AC Power Cord to the Power Supply Powering Up the Matrix X16-C ChassisFunction LED Activity DC Power LED LEDs and Reset ButtonPower Supply LEDs DC/AC Power Supply PS1-PS6 LED Definitions37 Fan Tray LED Fan Tray LEDsFunction LED Activity Module LEDs and Reset ButtonControl and Fabric Module LEDs Fan Tray LED DefinitionsState LED Activity Control and Fabric Module LED DefinitionsCM LEDs Only State LED Activity Ethernet Port LED RX/TX LED Activity IOM LEDsIOM LED Definitions Status LED LED ActivityConfiguring Dhcp First-Time Quick ConfigurationAssigning an IP Address to eth0 Naming the Matrix X16-C Enabling NTPAC Power Supply Module Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X-16C Specifications SpecificationFan Tray Table A-2 AC Power Supply RequirementsEnvironmental Table A-4 Redundancy Configurations for AC Line 100-120 Vac Table A-3 Module Power SpecificationsTable A-5 Redundancy Configurations for AC Line 200-240 Vac Module Wavelength Tx Power Rx Sensitivity Link Power Gigabit Ethernet Transceiver Specifications XFPTable A-6 Twist Lock Power Cord Options Table A-8 XFP Fiber-Optic SpecificationsTable A-9 Recommended Cable Types and Specifications Gigabit Ethernet Transceiver Specifications SFPType Max. Reach Min. Reach1 Connector Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical Specifications SFP Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-10 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-19 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-17 MGBIC-08 Optical SpecificationsTable A-20 COM Port Pin Assignments Pin Signal Name Input/OutputCOM Port Pinout Assignments Regulatory CompliancePage Index Mtbf RX/TX LED Index-4