Enterasys Networks X16-C manual LEDs and Reset Button, Power Supply LEDs, AC Power LED

Page 74

LEDs and Reset Button

LEDs and Reset Button

The following sections describe LED indications for the following:

Power supplies and fan trays

IOM, CM, and FMs (with CM Reset button)

Power Supply LEDs

Two LEDs are provided on the power supply module: a DC LED indicating the operational status of outgoing power and an AC LED indicating incoming AC line voltage is sufficient or has fallen below operational limits. Refer to Figure 3‐36 for their location and Table 3‐1 for a description of LED function. Power supplies are installed in chassis slots PS1 through PS6 along the right‐hand side of the chassis.

Figure 3-36 Power Supply LEDs

1

2

4

3

 

1 Intake cooling fans

2 DC Power LED

3 Handle

4 AC Power LED

Table 3-1 DC/AC Power Supply (PS1-PS6) LED Definitions

 

 

 

 

 

Function

 

 

LED Activity

 

 

 

 

DC Power LED

 

 

 

 

 

Power supply successfully providing 48 VDC to the system

Green

 

 

 

Power supply malfunctioning

 

Off

 

 

 

 

AC Power LED

 

 

 

 

 

 

Sufficient AC power supply (influx)

 

Green

 

 

 

No AC power into the module

 

Off

 

 

 

 

3-42 Matrix X16-C Chassis Setup

Image 74
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc Firmware License Agreement Viii Page Page Contents Appendix a Specifications and Regulatory Compliance IndexFigures Tables For information about Refer to Using This GuideWho Should Use This Guide Using the Matrix X Router Manual Set Conventions Used in This GuideCommonly Used Acronyms Getting HelpGetting Help Xviii About This Guide Overview System DescriptionMatrix X16-C Chassis as Shipped Front View Matrix X16-C Chassis as Shipped Rear View X16-C Control Module FeaturesX16-C Input/Output Modules Installing Redundant CMs into an Active Matrix X Router CM1 X16-C Fabric Module Monitor ValuesAuto-Ranging Power Supplies X16-C Redundant Power SuppliesPower Supply LEDs Power Supply ReplacementRack-Mountable Chassis Features Overview Site and Configuration Guidelines Site GuidelinesConfiguration Guidelines Matrix X16-C Chassis Setup Required ToolsUnpacking the Matrix X16-C Chassis Shipping straps Shipping box Shipping skidAccessory package Shipping bag Shipping skid ChassisDisassembly Steps 6 through Installing the Matrix X16-C Chassis Setting Up the Matrix X16-C ChassisSetup Order Installing Optional Rack Support Brackets Installing Optional Mid-Mount Brackets Rack Rack support brackets Bracket screwsFastening Mid-Mount Brackets Rack Mounting the Matrix X16-C Chassis To rack‐mount the Matrix X16‐C chassis, proceed as followsRack Mounting the Matrix X16-C Chassis Chassis Bonding and Grounding Rack Mounting the Mid-Mounted ChassisTelcordia GR-1089 Grounding Hole Pattern and Cable Grounding Receptacle Plug Wrist strap Installing and Removing a Power SupplyAttaching the Electrostatic Discharge Wrist Strap Power Supply Planning Installing a Power Supply13 Removing Power Supply Vent Plate Power supply slot PS1 Power supply coverplate Vent plate14 Installing Power Supply Module 15 Removing Blank Coverplate from Power Supply SlotRemoving a Power Supply Inlet power cord AC inlet AC1Installing and Removing a Fan Tray Installing a Fan Tray17 Removing Bottom Bezel Removing a Fan Tray Installing and Removing ModulesInstalling and Removing IOMs IOM slot Captive screws IOM guide rails Ejector handles20 Engaging Ejector Handles 21 Removing IOM CoverplateInstalling and Removing CMs Control Module slot Guide rails Captive screwsReplacing the CM Battery Installing and Removing FMs 23 Installing Fabric ModuleInstalling an XFP/SFP Module Removing an XFP/SFP Module XFP transceiver Port slot Release handle SFP transceiverConnecting Fiber-Optic Cables 25 Attaching LC or MT-RJ Cable ConnectorConnecting to the CM COM Port Parameter SettingConnecting the CM COM Port to a VT Series Terminal 26 Connecting an IBM PC or CompatibleConnecting the CM COM Port to a Modem 27 Connecting a VT Series TerminalAdapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal DiagramModem Port Adapter Wiring and Signal Diagram RJ45 DB25 Connecting to the CM USB PortVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 USB device Control Module USB port Installing a Compact Flash CardCompact Flash card Connector Control Module Installing the Memory Upgrade Kit Removing the DIMMsInstalling the DIMMs Connector fingers Connector armsOptional Cable Management Kit Installing the Optional Cable Management Kit To install the Cable Management Kit, proceed as follows33 Installing the Bottom Cable Management Assembly 34 Securing Cables Using Velcro Cable Straps Powering Up the Matrix X16-C Chassis 35 Connecting 20 Amp AC Power Cord to the Power SupplyDC/AC Power Supply PS1-PS6 LED Definitions LEDs and Reset ButtonPower Supply LEDs Function LED Activity DC Power LEDFan Tray LEDs 37 Fan Tray LEDFan Tray LED Definitions Module LEDs and Reset ButtonControl and Fabric Module LEDs Function LED ActivityCM LEDs Only State LED Activity Control and Fabric Module LED DefinitionsState LED Activity Status LED LED Activity IOM LEDsIOM LED Definitions Ethernet Port LED RX/TX LED ActivityAssigning an IP Address to eth0 First-Time Quick ConfigurationConfiguring Dhcp Enabling NTP Naming the Matrix X16-CSpecification Chassis, Power Supply, and Fan Tray SpecificationsTable A-1 Matrix X-16C Specifications AC Power Supply ModuleEnvironmental Table A-2 AC Power Supply RequirementsFan Tray Table A-5 Redundancy Configurations for AC Line 200-240 Vac Table A-3 Module Power SpecificationsTable A-4 Redundancy Configurations for AC Line 100-120 Vac Table A-8 XFP Fiber-Optic Specifications Gigabit Ethernet Transceiver Specifications XFPTable A-6 Twist Lock Power Cord Options Module Wavelength Tx Power Rx Sensitivity Link PowerType Max. Reach Min. Reach1 Connector Gigabit Ethernet Transceiver Specifications SFPTable A-9 Recommended Cable Types and Specifications Table A-10 Mini-GBIC Input/Output Port Specifications SFP Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-11 MGBIC-LC01 / MGBIC-MT01 Optical SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-17 MGBIC-08 Optical Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-19 MGBIC-02 SpecificationsRegulatory Compliance Pin Signal Name Input/OutputCOM Port Pinout Assignments Table A-20 COM Port Pin AssignmentsPage Index Mtbf RX/TX LED Index-4