EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridge user manual Product Features

Page 2

5.1	SYSTEM INFORMATION		38
5.2	STATISTIC INFORMATION		39
5.3	SITE SURVEY		40
5.4	WIRELESS LINK INFORMATION		41
CHAPTER 6.		SPECIFICATIONS	42
6.1	HARDWARE SPECIFICATIONS		42
6.2	SOFTWARE SPECIFICATIONS		44
CHAPTER 7.		DEFAULT SETTINGS	45
7.1	GENERAL CONFIGURATION		45
7.1.1		System	45
7.1.2		SNMP	45
7.1.3		Wireless LAN	46
7.2	UTILITY		48
7.2.1		Software Upgrade	48
7.2.2		Administration	48
CHAPTER 8. REGULATORY COMPLIANCE INFORMATION			49

Version 1.02

ii

Chapter 1. Introduction

1.1Introducing the Wireless client bridge

The Wireless client bridge is a fully interoperable with IEEE 802.11b compliant Outdoor Wireless Last-mile product. The Wireless client bridge operates in remote bridge mode, and connects Outdoor Wireless Router Bridge to construct point-to-point as well as point-to-multipoint topologies, for maximum flexibility in configuring building-to-building networks to WISP.

1.2Product Features

9Outdoor enclosure in compliance with IP67

9RF transmit power 100mW (20dBm) with -85dBm Rx sensitivity @ 11Mbps data rate

9Embedded 9dBi patch directional antenna

9Support 24VDC 0.8A Power-over-Ethernet

9NAT/NAPT and Virtual Server Mapping support

9MIB-II and Private MIB support

9MAC address based access control

1.3Package Contents

The product package contains the following items.

1.One (1) Wireless client bridge Outdoor Wireless Client Bridge unit

2.One (1) 100~240VAC, 50~60Hz AC/DC adapter with wall- mount plug and DC plug power cord

3.One (1) 24VDC, 830mA Inline Power Injector (PoE)

4.Three (3) water protect kit consists of 3 of components

5.One (1) 1.8m grounding wire

6.One (1) User manual CD-disc

7.One (1) wall/mast mounting kit, including one (1) band clamp

Version 1.02

1

Image 2

Contents Ieee 802.11b Outdoor Wireless Client Bridge Package Contents Introduction Introducing the Wireless client bridgeProduct Features System Requirements Inline Power Injector PoEInstallation and Basic Configuration Before You Start„ Interface on the Wireless client bridge Unit Before After „ Interface on the Inline Power InjectorPreparing Installation Move to page /Utility/Administration/, select Basic ConfigurationBasic Configuration Steps What you need to know„ Web Access Procedures Login into the Web Interface„ Web Configuration „ Identify the IP Address assigned to the unit„ Host Information Set IP Address, Subnet Mask, Default Route IP„ Web Configuration Structure Set Wireless Encryption for Wireless Interface Change Supervisor Account & Password„ Update the Firmware using the Tftp method Upgrade the Firmware„ Setup your Tftp Server „ Upgrade the Firmware using RS-232 consoleVersion „ Uploading Configuration Files Back-up the Wireless client bridge’s Configuration Files„ Downloading Configuration Files Remarks Wireless Client Bridge-to-Central Wireless BridgeNetwork Topologies Version Wireless Client Router-to-Central Wireless Router Configure Community Pool Network Parameters IP ConfigurationConfigure Snmp „ Wireless Client BridgeConfigure Trap Host Pool Configure Wireless related parameters Software Upgrade UtilityMonitor Information Administration„ Services Information „ General System InformationStatistic of Interface System InformationStatistic Information Site Survey Wireless Link Information Specifications Hardware Specifications System Software SpecificationsDefault Settings General Configuration Snmp Table of Snmp Community PoolWireless LAN Table of Snmp Trap Community Host Pool„ Radiation Exposure Statement Regulatory Compliance Information„ Radio Frequency Interference Requirements „ Interference Statement„ Professional Installation „ European Community CE Notice Marking by the symbol：