EnGenius Technologies IEEE 802.11b Outdoor Wireless Client Bridge Login into the Web Interface

Page 7

2.4.3 Login into the Web Interface

The Wireless client bridge supports access to the configuration system through the use of an HTTP Interface.

„Web Configuration

Before configuring Wireless client bridge, user needs to know the IP Address assigned to the unit. When shipped from the factory, the IP Address 192.168.5.99 was assigned to the Wireless client bridge by default. To start a web connection, use http://192.168.2.1

„Identify the IP Address assigned to the unit

However, user may change the IP Address later and cannot connect the unit by using the default IP Address. In this case, it is a must to identify the Wireless client bridge current IP Address before configuring. To identify the IP Address, user can use the serial port (refer to page 4) to gain access of the current network status.

To start a Serial Port connection by following the steps below.

Step 1 Attach the RS-232 null modem console cable (refer to page 4 and page 6) to the RS-232 Console Port on Wireless client bridge. Connect the other end to a terminal or a PC running a terminal emulation program.

Step 2 Set the terminal to 115200 baud rate, None Parity, 8 data bits, 1 Stop bit, and ANSI compatible.

Step 3 Run a terminal emulation program on PC, such as Hyper Terminal, and set the following connection properties.

Step 3.1 Click the Start icon > Program > Accessories > Communication > Terminal.

Step 3.2 Create a new connection file, and select a Com Port <COM1, COM2, etc., depending on PC> with 115200bps / 8-bits /1-stop.

Step 3.3 Click the properties icon in the Tool Bar > setting > select Emulation terminal VT100 > ok.

Step 4 Reboot Wireless client bridge.

Step 5 When the Wireless client bridge is powered up, the “Current Network Status” will be displayed as shown below.

„Web Access Procedures

Once you identify the IP Address assigned to Wireless client bridge, use web browser to configure Wireless client bridge through the HTTP Interface. The following procedure explains how to configure each item.

Step 1 Open your browser and enter the IP Address

Step 2 Press <ENTER> key and the Wireless client bridge Login screen appears as shown below.

Version 1.02

10

Version 1.02

11

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Ieee 802.11b Outdoor Wireless Client Bridge Product Features Introduction Introducing the Wireless client bridgePackage Contents Before You Start Inline Power Injector PoEInstallation and Basic Configuration System RequirementsBefore After „ Interface on the Inline Power Injector „ Interface on the Wireless client bridge UnitPreparing Installation What you need to know Basic ConfigurationBasic Configuration Steps Move to page /Utility/Administration/, select„ Identify the IP Address assigned to the unit Login into the Web Interface„ Web Configuration „ Web Access Procedures„ Web Configuration Structure Set IP Address, Subnet Mask, Default Route IP„ Host Information Change Supervisor Account & Password Set Wireless Encryption for Wireless Interface„ Upgrade the Firmware using RS-232 console Upgrade the Firmware„ Setup your Tftp Server „ Update the Firmware using the Tftp methodVersion „ Downloading Configuration Files Back-up the Wireless client bridge’s Configuration Files„ Uploading Configuration Files Network Topologies Wireless Client Bridge-to-Central Wireless BridgeRemarks Version Wireless Client Router-to-Central Wireless Router „ Wireless Client Bridge Network Parameters IP ConfigurationConfigure Snmp Configure Community PoolConfigure Trap Host Pool Configure Wireless related parameters Utility Software Upgrade„ General System Information Administration„ Services Information Monitor InformationStatistic Information System InformationStatistic of Interface Site Survey Wireless Link Information Specifications Hardware Specifications Snmp Table of Snmp Community Pool Software SpecificationsDefault Settings General Configuration SystemTable of Snmp Trap Community Host Pool Wireless LAN„ Interference Statement Regulatory Compliance Information„ Radio Frequency Interference Requirements „ Radiation Exposure Statement„ European Community CE Notice Marking by the symbol： „ Professional Installation
Top Page Image Contents