Enterasys Networks ANG-1000 manual Ethernet Cables, Power, Connecting Cables

Page 17

Chapter 2

Connecting Cables

Installation

All interconnections are made at the back of the ANG-1000 (refer to Figure 4). Although there is no power switch, a reset button is located in the rear of the unit.

CAUTION

If you press the reset button after you have configured your ANG-1000, you will lose your entire configuration. Any settings you supplied must then be re-entered. We strongly recommend that you do not use the reset button unless you want the configuration to return to factory defaults.

Ethernet Cables

The ANG-1000 is equipped with two 8-pin modular RJ-45 Ethernet ports labeled Trusted and External as shown in Figure 5. The Trusted port is connected to a computer or hub/switch with networked computers. The External port is connected to a cable or DSL modem.

Power
5Vd			T
c	2.5		T
	2.5	A	ru	st
				ed		Ext	er
				10	Ba	Ext	er
					Ba	se T	nal
						se T

Figure 5 Location of the Ethernet Ports

Reset

The trusted connection can be either a sole desktop computer or a hub that connects up to 25 tunnels to the network as shown in Figure 6.

Aurorean Network Gateway-1000 User’s Guide

5

Image 17

Contents Aurorean Virtual Network ANG-1000 User’s GuideAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page About This Guide Contents of the GuideConventions Used in This Guide About This Guide Related Publications Related PublicationsPage ANG-1000 Front Rear OverviewSystem Description System Description ANG-1000 TopologyUnpacking the ANG-1000 InstallationLocation Planning Connecting CablesAccessories Ethernet Cables PowerConnecting Cables Aurorean Network Gateway-1000 Do one of the following as shown in FigureANG-3000/7000 Chapter Connecting Power to the ANG-1000 Connecting Power to the ANG-1000Connecting the Power Cable to the Power Supply Front Power LED will light the moment you power up the unitRear Panel Link LEDs Checking ANG-1000 ConnectionsFront Panel LEDs Chapter Checking ANG-1000 ConnectionsCOM1 and COM2 Leds are not operational at this time PowerActive InternetBefore You Begin Configuring the ANG-1000 with Aurorean Web ConfigConfiguring the ANG-1000 with Aurorean Web Config To log into Web Config, perform the steps below Logging into Web ConfigLogin window appears as shown in Figure VPN Status window appears as shown in FigureVPN Viewing VPN StatusFirmware Upgrade window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Update window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window ANG-1000 will take a few moments to accept the new software Aurorean Network Gateway Firmware UpdateClick the VPN Setup menu option Setting Up the VPNVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Do one of the following Click the Internet Setup menu optionInternet Setup window appears as shown in Figure Configuring the ANG-1000 with Aurorean Web Config Click the LAN Setup menu option Setting Up the LANLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Begin Firewall Setup by performing the following steps Setting Up the FirewallClick the Firewall Setup menu option Firewall Setup window appears as shown in FigureConnectivity Setup LAN Connection Aurorean Network Gateway Firewall SetupClick the Set Password menu option Setting Your PasswordSet Password window appears as shown in Figure Set PasswordDevice Status window appears as shown in Figure Checking Device StatusClick the Device Status menu option Device Status Window Route Table Network DevicesInterrupts System LogClick the Advanced Utilities menu option Using Advanced UtilitiesAdvanced Utilities window appears as shown in Figure Advanced UtilitiesUsing the Configuration Editor Configuration Edit window appears as shown in Figure Click the Configuration Edit menu optionFile/etc/config/config Configuring IP Port Forwarding Usage Follow the steps below to configure IP port forwardingSwitch Arg Definition Example Page Glossary Aurorean Web ConfigAurorean Network Gateway Aurorean Policy ServerFirewall EthernetGeneric Routing Encapsulation GRE Internet Service Provider ISPIP Address IP Security Protocol IPSecNetwork Address Translation NAT LEDsMac Address Point of Presence POP Network AdministratorPoint-to-Point Protocol PPP Point-to-Point Tunneling Protocol PptpRouters RiverMasterTunneling Virtual Private Network VPNCategory Parameters SpecificationsThis appendix details the specifications of the ANG-1000 Specifications Pin Assignments Pin SignalLink 1 Trusted Link 2 ExternalPin Assignments License Grant License Agreement & SupportEnterasys Networks License Agreement Warranty Appendix D Infringement IndemnificationLimitation of Liability Applicable Law TerminationInternational Provisions Support from Enterasys Networks Technical SupportGovernment Commercial Computer Software Technical Support Returning Products for RepairIndex POP IndexIndex