Enterasys Networks ANG-1000 manual Using the Configuration Editor, Do one of the following

Page 44

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

2Do one of the following:

To change the ANG-1000’s MAC address to reflect your computer ’s MAC address, first find the computer’s address by issuing the proper command at a DOS prompt. For Windows 95/98/ME systems, type winipcfg; for Windows NT/2000 systems, type ipconfig /all; for Macintosh systems, check the TCP-IP control panel.

In the command output, look for the Physical or Adapter Address value. For example:

c:>ipconfig /all Ethernet adapter E190x1:

Description . . : 3Com 3C90x Ethernet Adapter

Physical Address : 00-10-4B-9D-18-17

Enter the value in the Internet MAC Address Assignment fields.

Click Apply and Reboot Now when prompted to save the change.

Select Clear System Logfile and click Apply.

Select Soft Reboot ANG-1000 and click Apply.

NOTE

ANG-1000 connections broken during a reboot will be lost after service returns. Idling the traffic stream (Telnet, e.g.) for a couple minutes before re-initiating the connection resolves the problem.

Using the Configuration Editor

Knowledgeable network administrators can use the Configuration Editor to invoke commands on the ANG-1000’s LINUX 2.0 operating system.

CAUTION

Inexperienced users or those unfamiliar with LINUX attempting to use this editor may disable the system. We recommend only expert users, in conjunction with Enterasys Customer Support, use this editor.

32

Aurorean Network Gateway-1000 User’s Guide

Image 44
Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage ANG-1000 Front Rear OverviewSystem Description ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Location Planning Connecting CablesAccessories Ethernet Cables PowerConnecting Cables Aurorean Network Gateway-1000 Do one of the following as shown in FigureANG-3000/7000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyChecking ANG-1000 Connections Rear Panel Link LEDsFront Panel LEDs Chapter Checking ANG-1000 ConnectionsPower COM1 and COM2 Leds are not operational at this timeActive InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Logging into Web Config To log into Web Config, perform the steps belowLogin window appears as shown in Figure VPN Status window appears as shown in FigureViewing VPN Status VPNClick the Firmware Upgrade menu option Firmware Upgrade window appears as shown in FigureFirmware Update window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareSetting Up the VPN Click the VPN Setup menu optionVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Do one of the following Click the Internet Setup menu optionInternet Setup window appears as shown in Figure Configuring the ANG-1000 with Aurorean Web Config Setting Up the LAN Click the LAN Setup menu optionLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Setting Up the Firewall Begin Firewall Setup by performing the following stepsClick the Firewall Setup menu option Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSetting Your Password Click the Set Password menu optionSet Password window appears as shown in Figure Set PasswordDevice Status window appears as shown in Figure Checking Device StatusClick the Device Status menu option Device Status Window Network Devices Route TableInterrupts System LogUsing Advanced Utilities Click the Advanced Utilities menu optionAdvanced Utilities window appears as shown in Figure Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Usage Follow the steps below to configure IP port forwardingSwitch Arg Definition Example Page Aurorean Web Config GlossaryAurorean Network Gateway Aurorean Policy ServerEthernet FirewallInternet Service Provider ISP Generic Routing Encapsulation GREIP Address IP Security Protocol IPSecNetwork Address Translation NAT LEDsMac Address Network Administrator Point of Presence POPPoint-to-Point Protocol PPP Point-to-Point Tunneling Protocol PptpRiverMaster RoutersTunneling Virtual Private Network VPNCategory Parameters SpecificationsThis appendix details the specifications of the ANG-1000 Specifications Pin Signal Pin AssignmentsLink 1 Trusted Link 2 ExternalPin Assignments License Grant License Agreement & SupportEnterasys Networks License Agreement Warranty Appendix D Infringement IndemnificationLimitation of Liability Applicable Law TerminationInternational Provisions Support from Enterasys Networks Technical SupportGovernment Commercial Computer Software Returning Products for Repair Technical SupportIndex Index POPIndex