Enterasys Networks ANG-1000 manual Downloading the Latest Firmware

Page 27

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

Downloading the Latest Firmware

After logging in, download the latest firmware image to the ANG-1000’s flash memory (provided the MAC address is set for cable service users - refer to page 32) by accessing the FTP server where it is stored. As new firmware becomes available, you can update it again. Begin updating your firmware by performing the following steps:

1Click the Firmware Upgrade menu option.

The Firmware Upgrade window appears as shown in Figure 16.

		Aurorean Network Gateway 1000
	Help	Firmware Update
	VPN	FTP server:
	VPN
	VPN Status	Firmware image
	VPN Setup	filepath:
	VPN Setup
	Connectivity Setup	Username:
	Connectivity Setup	Password:
	Internet Setup	Password:
	Internet Setup
	LAN Setup	Confirm:
	Firewall Setup	Confirm:
	Firewall Setup	Apply
		Apply

		Figure 16 Firmware Update Window

2In the FTP server field, enter the name of the FTP server where the new ANG image is stored: ang.enterasys.com.

3Type the full path of the location of the Firmware image:

/ang1000/ANG1000.bin

4Enter the Username anonymous

5Enter netadmin in the Password and Confirm fields and click Apply.

The Firmware Update window appears as shown in Figure 17.

6Click Apply and watch the External/Trusted LEDs on the front panel blink displaying an inside/outside pattern.

The image is downloaded for15-30 seconds and loaded in flash memory for another 30-45 seconds. If the LEDs do not blink or only for a very short interval, the download failed and you must try again.

Aurorean Network Gateway-1000 User’s Guide

15

Image 27

Contents Aurorean Virtual Network ANG-1000 User’s GuideAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page About This Guide Contents of the GuideConventions Used in This Guide About This Guide Related Publications Related PublicationsPage Overview System DescriptionANG-1000 Front Rear System Description ANG-1000 TopologyUnpacking the ANG-1000 InstallationConnecting Cables AccessoriesLocation Planning Power Connecting CablesEthernet Cables Do one of the following as shown in Figure ANG-3000/7000Aurorean Network Gateway-1000 Chapter Connecting Power to the ANG-1000 Connecting Power to the ANG-1000Connecting the Power Cable to the Power Supply Front Power LED will light the moment you power up the unitChapter Checking ANG-1000 Connections Checking ANG-1000 ConnectionsRear Panel Link LEDs Front Panel LEDsInternet PowerCOM1 and COM2 Leds are not operational at this time ActiveBefore You Begin Configuring the ANG-1000 with Aurorean Web ConfigConfiguring the ANG-1000 with Aurorean Web Config VPN Status window appears as shown in Figure Logging into Web ConfigTo log into Web Config, perform the steps below Login window appears as shown in FigureVPN Viewing VPN StatusDownloading the Latest Firmware Click the Firmware Upgrade menu optionFirmware Upgrade window appears as shown in Figure Firmware Update window appears as shown in FigureSecond Firmware Update Window ANG-1000 will take a few moments to accept the new software Aurorean Network Gateway Firmware UpdateAurorean Network Gateway VPN Setup Setting Up the VPNClick the VPN Setup menu option VPN Setup window appears as shown in FigureClick Apply Setting Up the Internet Connection Click the Internet Setup menu option Internet Setup window appears as shown in FigureDo one of the following Configuring the ANG-1000 with Aurorean Web Config LAN Setup Setting Up the LANClick the LAN Setup menu option LAN Setup window appears as shown in FigureConfiguring the ANG-1000 with Aurorean Web Config Firewall Setup window appears as shown in Figure Setting Up the FirewallBegin Firewall Setup by performing the following steps Click the Firewall Setup menu optionConnectivity Setup LAN Connection Aurorean Network Gateway Firewall SetupSet Password Setting Your PasswordClick the Set Password menu option Set Password window appears as shown in FigureChecking Device Status Click the Device Status menu optionDevice Status window appears as shown in Figure Device Status Window System Log Network DevicesRoute Table InterruptsAdvanced Utilities Using Advanced UtilitiesClick the Advanced Utilities menu option Advanced Utilities window appears as shown in FigureUsing the Configuration Editor Configuration Edit window appears as shown in Figure Click the Configuration Edit menu optionFile/etc/config/config Configuring IP Port Forwarding Follow the steps below to configure IP port forwarding Switch Arg DefinitionUsage Example Page Aurorean Policy Server Aurorean Web ConfigGlossary Aurorean Network GatewayFirewall EthernetIP Security Protocol IPSec Internet Service Provider ISPGeneric Routing Encapsulation GRE IP AddressLEDs Mac AddressNetwork Address Translation NAT Point-to-Point Tunneling Protocol Pptp Network AdministratorPoint of Presence POP Point-to-Point Protocol PPPVirtual Private Network VPN RiverMasterRouters TunnelingSpecifications This appendix details the specifications of the ANG-1000Category Parameters Specifications Link 2 External Pin SignalPin Assignments Link 1 TrustedPin Assignments License Agreement & Support Enterasys Networks License AgreementLicense Grant Warranty Infringement Indemnification Limitation of LiabilityAppendix D Termination International ProvisionsApplicable Law Technical Support Government Commercial Computer SoftwareSupport from Enterasys Networks Technical Support Returning Products for RepairIndex POP IndexIndex