Enterasys Networks ANG-1000 manual Do one of the following as shown in Figure, ANG-3000/7000

Page 18

Connecting Cables	Chapter 2
	Installation

Connecting an ANG-1000

The ANG-1000 is typically set up in the configuration shown below.

INTERNET

Site-to-site tunnel

ANG-3000/7000

	External
Cable / DSL	connection
Modem

User

Trusted

connection

or

Hub

Aurorean Network

Gateway-1000

Site-to-site tunnel
Internet connection	User
Trusted connection	User
Trusted connection

Figure 6 Connecting the ANG-1000

To connect the ANG-1000 Ethernet port, perform the following steps:

1Do one of the following as shown in Figure 7:

–If you are connecting to a hub, plug the blue, straight-through Ethernet cable into the Trusted port of the ANG-1000.

–If you are connecting directly to a computer, attach one end of the red, cross-over cable to the Trusted port and the other end to an RJ45 connector on your computer. Skip to Step 3.

2Plug the opposite end of the blue Ethernet cable into a wall jack, patch panel, or hub linked to a protected network segment.

The top link LED next to the ANG-1000’s Trusted port will immediately light if the port is connected to a 10 Mbps network after the unit is powered up.

6	Aurorean Network Gateway-1000 User’s Guide

Image 18

Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage Overview System DescriptionANG-1000 Front Rear ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Connecting Cables AccessoriesLocation Planning Power Connecting CablesEthernet Cables Do one of the following as shown in Figure ANG-3000/7000Aurorean Network Gateway-1000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyFront Panel LEDs Checking ANG-1000 ConnectionsRear Panel Link LEDs Chapter Checking ANG-1000 ConnectionsActive PowerCOM1 and COM2 Leds are not operational at this time InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Login window appears as shown in Figure Logging into Web ConfigTo log into Web Config, perform the steps below VPN Status window appears as shown in FigureViewing VPN Status VPNFirmware Update window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Upgrade window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareVPN Setup window appears as shown in Figure Setting Up the VPNClick the VPN Setup menu option Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Click the Internet Setup menu option Internet Setup window appears as shown in FigureDo one of the following Configuring the ANG-1000 with Aurorean Web Config LAN Setup window appears as shown in Figure Setting Up the LANClick the LAN Setup menu option LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Click the Firewall Setup menu option Setting Up the FirewallBegin Firewall Setup by performing the following steps Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSet Password window appears as shown in Figure Setting Your PasswordClick the Set Password menu option Set PasswordChecking Device Status Click the Device Status menu optionDevice Status window appears as shown in Figure Device Status Window Interrupts Network DevicesRoute Table System LogAdvanced Utilities window appears as shown in Figure Using Advanced UtilitiesClick the Advanced Utilities menu option Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Follow the steps below to configure IP port forwarding Switch Arg DefinitionUsage Example Page Aurorean Network Gateway Aurorean Web ConfigGlossary Aurorean Policy ServerEthernet FirewallIP Address Internet Service Provider ISPGeneric Routing Encapsulation GRE IP Security Protocol IPSecLEDs Mac AddressNetwork Address Translation NAT Point-to-Point Protocol PPP Network AdministratorPoint of Presence POP Point-to-Point Tunneling Protocol PptpTunneling RiverMasterRouters Virtual Private Network VPNSpecifications This appendix details the specifications of the ANG-1000Category Parameters Specifications Link 1 Trusted Pin SignalPin Assignments Link 2 ExternalPin Assignments License Agreement & Support Enterasys Networks License AgreementLicense Grant Warranty Infringement Indemnification Limitation of LiabilityAppendix D Termination International ProvisionsApplicable Law Technical Support Government Commercial Computer SoftwareSupport from Enterasys Networks Returning Products for Repair Technical SupportIndex Index POPIndex