Enterasys Networks ANG-1000 manual Second Firmware Update Window

Page 28

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

Help

VPN

VPN Status

VPN Setup

Firmware Update

To begin the update of the ANG-1000 firmware image, press the “Apply” button at the bottom of the screen.

For users new to the process of upgrading the ANG-1000 firmware, you will observe the following behavior once you press the “Apply” button. It is critical not to disturb the ANG-1000 by disconnecting power or the interface cables during the firmware update process.

First you’ll see the following activity lights on the ANG-1000:

Connectivity Setup

Internet Setup

LAN Setup

Firewall Setup

ANG-1000 System

Set Password

Device Status

Firmware Update

Advanced Utilities

Links

Config File Editor

Aurorean Products

Enterasys Home

This indicates that the firmware image is being downloaded from the FTP source you entered in the previous screen. The photo shows a download from an FTP server on the external interface. These lights will be active during the time needed to retrieve the firmware image from the specified FTP server. This would take about 15-30 seconds on a typical connection. If there are no activity lights seen or if they are seen for a very short period of time, there was an error downloading the firmware image.

After the firmware image is downloaded, the new image is “flushed” or stored on the ANG-1000. This step takes about 30-45 seconds and the photo below shows the activity lights seen on the ANG-1000 when the device’s flash memory is being upgraded with the new firmware image.

Once the “Apply” is pressed, there will be a delay in displaying the next Web page for the ANG-1000 Web application. It will only be displayed once the firmware image is downloaded and the new image is flashed to the ANG-1000. After these two steps are complete, a status page is displayed to indicate whether or not the firmware update was successful. If it was successful, the Web page prompts the user to reboot the ANG-1000 to run with the new firmware image.

To start the firmware image download and update process, press the “Apply” button now.

<< Back

Figure 17 Second Firmware Update Window

16

Aurorean Network Gateway-1000 User’s Guide

Image 28
Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage System Description OverviewANG-1000 Front Rear ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Accessories Connecting CablesLocation Planning Connecting Cables PowerEthernet Cables ANG-3000/7000 Do one of the following as shown in FigureAurorean Network Gateway-1000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyChecking ANG-1000 Connections Rear Panel Link LEDsFront Panel LEDs Chapter Checking ANG-1000 ConnectionsPower COM1 and COM2 Leds are not operational at this timeActive InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Logging into Web Config To log into Web Config, perform the steps belowLogin window appears as shown in Figure VPN Status window appears as shown in FigureViewing VPN Status VPNClick the Firmware Upgrade menu option Firmware Upgrade window appears as shown in FigureFirmware Update window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareSetting Up the VPN Click the VPN Setup menu optionVPN Setup window appears as shown in Figure Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Internet Setup window appears as shown in Figure Click the Internet Setup menu optionDo one of the following Configuring the ANG-1000 with Aurorean Web Config Setting Up the LAN Click the LAN Setup menu optionLAN Setup window appears as shown in Figure LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Setting Up the Firewall Begin Firewall Setup by performing the following stepsClick the Firewall Setup menu option Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSetting Your Password Click the Set Password menu optionSet Password window appears as shown in Figure Set PasswordClick the Device Status menu option Checking Device StatusDevice Status window appears as shown in Figure Device Status Window Network Devices Route TableInterrupts System LogUsing Advanced Utilities Click the Advanced Utilities menu optionAdvanced Utilities window appears as shown in Figure Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Switch Arg Definition Follow the steps below to configure IP port forwardingUsage Example Page Aurorean Web Config GlossaryAurorean Network Gateway Aurorean Policy ServerEthernet FirewallInternet Service Provider ISP Generic Routing Encapsulation GREIP Address IP Security Protocol IPSecMac Address LEDsNetwork Address Translation NAT Network Administrator Point of Presence POPPoint-to-Point Protocol PPP Point-to-Point Tunneling Protocol PptpRiverMaster RoutersTunneling Virtual Private Network VPNThis appendix details the specifications of the ANG-1000 SpecificationsCategory Parameters Specifications Pin Signal Pin AssignmentsLink 1 Trusted Link 2 ExternalPin Assignments Enterasys Networks License Agreement License Agreement & SupportLicense Grant Warranty Limitation of Liability Infringement IndemnificationAppendix D International Provisions TerminationApplicable Law Government Commercial Computer Software Technical SupportSupport from Enterasys Networks Returning Products for Repair Technical SupportIndex Index POPIndex