Enterasys Networks manual Configuring the ANG-1000 with Aurorean Web Config

Page 34

Chapter 3

Configuring the ANG-1000 with Aurorean Web Config

–Enter the Gateway IP address.

–Specify the Primary DNS IP address.

–Set the Secondary DNS IP address.

–Click Apply.

HClick the PPPoE assigned IP address radio button and perform the following steps:

–Specify a Username supplied by your cable/DSL provider.

–Enter a Password.

–Type the password again in the Confirm field.

–Click Apply.

3If you chose the Manual or PPPoE options, a window appears detailing the reconfiguration changes and prompting you to reboot the ANG-1000. Click Reboot Now.

After a few moments when an IP address has been received for the external port, the Internet LED will turn on. If a static IP address was configured, the Internet LED will shine immediately.

NOTE

If you press the reset button after you have configured your ANG-1000, you will lose your entire configuration. Any settings you supplied must then be re-entered. We strongly recommend that you do not use the reset button unless you want the configuration to return to factory defaults.

22	Aurorean Network Gateway-1000 User’s Guide

Image 34

Contents ANG-1000 User’s Guide Aurorean Virtual NetworkAurorean Network Gateway-1000 User’s Guide Iii Important Safety Instructions Table of Contents Configuring the ANG-1000 with Aurorean Web Vii Page Contents of the Guide About This GuideConventions Used in This Guide Related Publications About This Guide Related PublicationsPage System Description OverviewANG-1000 Front Rear ANG-1000 Topology System DescriptionInstallation Unpacking the ANG-1000Accessories Connecting CablesLocation Planning Connecting Cables PowerEthernet Cables ANG-3000/7000 Do one of the following as shown in FigureAurorean Network Gateway-1000 Connecting Power to the ANG-1000 Chapter Connecting Power to the ANG-1000Front Power LED will light the moment you power up the unit Connecting the Power Cable to the Power SupplyFront Panel LEDs Checking ANG-1000 ConnectionsRear Panel Link LEDs Chapter Checking ANG-1000 ConnectionsActive PowerCOM1 and COM2 Leds are not operational at this time InternetConfiguring the ANG-1000 with Aurorean Web Config Before You BeginConfiguring the ANG-1000 with Aurorean Web Config Login window appears as shown in Figure Logging into Web ConfigTo log into Web Config, perform the steps below VPN Status window appears as shown in FigureViewing VPN Status VPNFirmware Update window appears as shown in Figure Click the Firmware Upgrade menu optionFirmware Upgrade window appears as shown in Figure Downloading the Latest FirmwareSecond Firmware Update Window Aurorean Network Gateway Firmware Update ANG-1000 will take a few moments to accept the new softwareVPN Setup window appears as shown in Figure Setting Up the VPNClick the VPN Setup menu option Aurorean Network Gateway VPN SetupClick Apply Setting Up the Internet Connection Internet Setup window appears as shown in Figure Click the Internet Setup menu optionDo one of the following Configuring the ANG-1000 with Aurorean Web Config LAN Setup window appears as shown in Figure Setting Up the LANClick the LAN Setup menu option LAN SetupConfiguring the ANG-1000 with Aurorean Web Config Click the Firewall Setup menu option Setting Up the FirewallBegin Firewall Setup by performing the following steps Firewall Setup window appears as shown in FigureAurorean Network Gateway Firewall Setup Connectivity Setup LAN ConnectionSet Password window appears as shown in Figure Setting Your PasswordClick the Set Password menu option Set PasswordClick the Device Status menu option Checking Device StatusDevice Status window appears as shown in Figure Device Status Window Interrupts Network DevicesRoute Table System LogAdvanced Utilities window appears as shown in Figure Using Advanced UtilitiesClick the Advanced Utilities menu option Advanced UtilitiesUsing the Configuration Editor Click the Configuration Edit menu option Configuration Edit window appears as shown in FigureFile/etc/config/config Configuring IP Port Forwarding Switch Arg Definition Follow the steps below to configure IP port forwardingUsage Example Page Aurorean Network Gateway Aurorean Web ConfigGlossary Aurorean Policy ServerEthernet FirewallIP Address Internet Service Provider ISPGeneric Routing Encapsulation GRE IP Security Protocol IPSecMac Address LEDsNetwork Address Translation NAT Point-to-Point Protocol PPP Network AdministratorPoint of Presence POP Point-to-Point Tunneling Protocol PptpTunneling RiverMasterRouters Virtual Private Network VPNThis appendix details the specifications of the ANG-1000 SpecificationsCategory Parameters Specifications Link 1 Trusted Pin SignalPin Assignments Link 2 ExternalPin Assignments Enterasys Networks License Agreement License Agreement & SupportLicense Grant Warranty Limitation of Liability Infringement IndemnificationAppendix D International Provisions TerminationApplicable Law Government Commercial Computer Software Technical SupportSupport from Enterasys Networks Returning Products for Repair Technical SupportIndex Index POPIndex